background image

32

Limited Product Warranty

(Applicable under normal application, installation, use and service conditions)

Astronergy warrants the above listed products to be free from defects and/or failure specified for a period not exceeding five (5) 
years from the date of sale as shown in the Proof of Purchase to the Original purchaser.

The warranties described in these “Limited Warranties ” are exclusive and are expressly in lieu of and exclude all other 
warranties, whether written, oral, express or implied, including but not limited to, warranties of merchantability and of fitness
for a particular purpose, use ,or application, and all other obligations or liabilities on the part of Astronergy , unless such other 
obligations or liabilities are expressly agreed to it in writing signed and approved by Astronergy , Astronergy shall have no
responsibility or liability whatsoever for damage or injury to persons or property, or for other loss or injury resulting from 
any cause whatsoever arising out of or related to the modules, including, without limitation, any defects in the modules or 
from use or installation. Under no circumstances shall Astronergy be liable for incidental, consequential or special damages 
howsoever caused; loss of use, loss of production, loss of revenues are therefore specifically and without limitation excluded 
to the extent legally permissible, Astronergy ’s aggregate liability, if any, in damages or otherwise, shall not exceed the invoice 
as paid by the customer.

The “Limited Product Warranties” described above shall not apply to, and Astronergy shall have no obligation of and kind 
whatsoever with respect to, any inverter which has been subjected to:

— Misuse, abuse, neglect or accident;
— Alteration, improper installation or application;
— Unauthorised modification or attempted repairs;
— Insufficient ventilation of the product;
— Transport damage;
— Breaking of the original manufacturers seal;
— Non-observance of Astronergy installation and maintenance instruction;
— Failure to observe the applicable safety regulations
— Power failure surges, lighting, flood, fire, exposure to incorrect use, negligence, accident, force majeure, explosion, terrorist 
      act, vandalism or damage caused by incorrect installation, modification or extreme weather conditions or other 
      circumstances not reasonably attributable to Astronergy.

Liability
The warranty shall also cease to apply if the product cannot be correctly identified as the product of Astronergy. Warranty 
claims will not be honored if the type of serial number on the inverters have been altered, removed or rendered illegible.

Summary of Contents for 5KTL-M2





































Reviews: