6 - 3
6 - 3
6 - 3
6 - 3
6 - 3
A S U S A P 1 6 0 0 R - E 2 ( A A 2 / A I 2 )
A S U S A P 1 6 0 0 R - E 2 ( A A 2 / A I 2 )
A S U S A P 1 6 0 0 R - E 2 ( A A 2 / A I 2 )
A S U S A P 1 6 0 0 R - E 2 ( A A 2 / A I 2 )
A S U S A P 1 6 0 0 R - E 2 ( A A 2 / A I 2 )
6.1.3
6.1.3
6.1.3
6.1.3
6.1.3
Setting the RAID item in BIOS
Setting the RAID item in BIOS
Setting the RAID item in BIOS
Setting the RAID item in BIOS
Setting the RAID item in BIOS
You must set the RAID item in the BIOS Setup before you can create a RAID
set(s). To do this:
1.
Enter the BIOS Setup during POST.
2.
Go to the A d v a n c e d M e n u
A d v a n c e d M e n u
A d v a n c e d M e n u
A d v a n c e d M e n u
A d v a n c e d M e n u, select O n b o a r d d e v i c e
O n b o a r d d e v i c e
O n b o a r d d e v i c e
O n b o a r d d e v i c e
O n b o a r d d e v i c e, then press
<Enter>.
3.
Select the item S A T A C o n f i g u r a t i o n
S A T A C o n f i g u r a t i o n
S A T A C o n f i g u r a t i o n
S A T A C o n f i g u r a t i o n
S A T A C o n f i g u r a t i o n, then press <Enter> to display
the configuration options.
4.
Select R A I D
R A I D
R A I D
R A I D
R A I D from the S A T A M o d e
S A T A M o d e
S A T A M o d e
S A T A M o d e
S A T A M o d e options, then press <Enter>.
5.
Save your changes, then exit the BIOS Setup.
Refer to the BIOS setup for details on configuring the BIOS.
6.1.4
6.1.4
6.1.4
6.1.4
6.1.4
RAID configuration utility
RAID configuration utility
RAID configuration utility
RAID configuration utility
RAID configuration utility
You can create a RAID set using the utility embedded in the RAID
controller. For example, you can use the A d a p t e c R A I D C o n f i g u r a t i o n
A d a p t e c R A I D C o n f i g u r a t i o n
A d a p t e c R A I D C o n f i g u r a t i o n
A d a p t e c R A I D C o n f i g u r a t i o n
A d a p t e c R A I D C o n f i g u r a t i o n
U t i l i t y
U t i l i t y
U t i l i t y
U t i l i t y
U t i l i t y if you installed SATA hard disk drives on the SATA connectors
supported by the Intel
®
6300ESB Southbridge.
The Adaptec RAID Configuration Utility allows you to create RAID 0 and
RAID 1 set using the SATA hard disk drives connected to the SATA
connectors supported by the motherboard Southbridge chip.
To enter the Adaptec RAID Configuration Utility:
1.
Turn on the system after installing all the SATA hard disk drives.
2.
During POST, the Adaptec HostRAID™ technology automatically
detects the installed SATA hard disk drives and displays any existing
RAID set(s). Press <Ctrl> <A> to enter the utility.
Summary of Contents for AP1600-R-E2
Page 10: ...x ...
