DS300f G2 Series User Manual
38
v
Irtual
m
anaGement
P
ort
S
ettInGS
M
Aking
v
irtuAl
M
AnAgeMent
P
ort
s
ettings
– A
utoMAticAlly
Automatic settings require a DHCP server on your network. DHCP is currently supported on IPv4 only.
To enable automatic management port settings:
1. At the command prompt, type
net -a mod -f ipv4 -s “dhcp=enable”
and press
Enter
.
administrator@cli> net -a mod -f ipv4 -s “dhcp=enable”
After a moment, the comand prompt reappears, indicating that your setting was successful.
administrator@cli>
2. To verify the setting change, at the command prompt, type
net
and press
Enter
. The following information
displays:
administrator@cli> net
==========================================
PF Status IP
Link
==========================================
IPv4 Enabled 10.0.0.1
Up
IPv6 Disabled :: Up
In the above example:
• PF refers to IP protocol family, v4 or v6
• Status refers to whether the IP protocol is enabled. IPv4 is enabled by default.
• IP is the virtual management port IP address.
• Link indicates whether there is a working network connection.
By default, IPv4 is enabled and IPv6 is disabled. Currently IPv6 does not suppport DHCP.
M
Aking
v
irtuAl
M
AnAgeMent
P
ort
s
ettings
– M
AnuAlly
under
iP
v
4
To make IPv4 settings manually on the management port:
1. At the command prompt, type
net -a mod -f ipv4 -s
“ followed by:
•
primaryip=
and the IP address
,
•
primaryipmask=
and the subnet mask
,
•
primarydns=
and the DNS server IP address
,
•
gateway=
and the Gateway server IP address
“
and press
Enter
.
Example:
administrator@cli> net -a mod -f ipv4 -s “primaryip=10.0.0.1, primaryipmask=
255.255.255.0,primarydns=10.0.0.11,gateway=10.0.0.1”
After a moment, the comand prompt reappears, indicating that your setting was successful.
administrator@cli>
2. To verify the settings, at the command prompt, type net -a list -v and press
Enter
.
The following information displays:
administrator@cli> net -a list -v
----------------------------------------------------------------------------
ActiveCtrlId: 1 Port: 1
MaxSupportedSpeed: 1000Mbps LinkStatus: Up
ProtocolFamily: IPv4(Enabled)
DHCP: Disabled
IP: 10.0.0.1
IPMask: 255.255.255.0
MAC: 00:01:55:61:18:65
DNS: 10.0.0.11
Gateway: 10.0.0.1
ProtocolFamily: IPv6(Disabled) DHCP: Disabled
IP: ::
IPMask: ::
MAC: 00:01:55:61:18:65
DNS: ::
Gateway: ::
M
Aking
v
irtuAl
M
AnAgeMent
P
ort
s
ettings
– M
AnuAlly
under
iP
v
6
To make IPv6 settings manually on the management port:
1. At the command prompt, type
net -a enable -f ipv6
and press
Enter
to enable IPv6 on the ASUS DS300f G2.
After a moment, the comand prompt reappears, indicating that your setting was successful.
administrator@cli>
2. At the command prompt, type net -a mod -f ipv6 -s “ followed by:
•
primaryip=
and the IP address
,
•
primaryipmask=
and the subnet mask
,
•
primarydns=
and the DNS server IP address
,
•
gateway=
and the Gateway server IP address
“
and press
Enter
.
Summary of Contents for DS300 G2 Series
