A S U S A 7 S 8 X - M X
A S U S A 7 S 8 X - M X
A S U S A 7 S 8 X - M X
A S U S A 7 S 8 X - M X
A S U S A 7 S 8 X - M X
1 - 2 3
1 - 2 3
1 - 2 3
1 - 2 3
1 - 2 3
3 .
3 .
3 .
3 .
3 .
S e r i a l A T A c o n n e c t o r s
S e r i a l A T A c o n n e c t o r s
S e r i a l A T A c o n n e c t o r s
S e r i a l A T A c o n n e c t o r s
S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 , S A T A 2 )
( 7 - p i n S A T A 1 , S A T A 2 )
( 7 - p i n S A T A 1 , S A T A 2 )
( 7 - p i n S A T A 1 , S A T A 2 )
( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
•
Install the Windows
®
2000 Service Pack 4 or the XP Service Pack1
before using Serial ATA hard disk drives.
•
Serial ATA is supported under Windows
®
XP/2000/2003 only.
Legacy operating systems, such as Windows
®
98 SE/Me, do not
support native Serial ATA mode. See page 2-23.
•
Plug your Serial ATA boot disk on the master port (SATA1) to
support S3 function. Refer to the table below for details.
Serial ATA Master/Slave connectors
Serial ATA Master/Slave connectors
Serial ATA Master/Slave connectors
Serial ATA Master/Slave connectors
Serial ATA Master/Slave connectors
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
U s e
U s e
U s e
U s e
U s e
SATA1
Master
Boot disk
SATA2
Slave
Data disk
A7S8X-MX
®
A7S8X-MX SATA connectors
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
Summary of Contents for Motherboard A7S8X-MX
Page 1: ...Motherboard A7S8X MX ...
Page 12: ...x i i x i i x i i x i i x i i ...
