background image

2-5

ASUS T3-P5945GC

2.5 

CPU installation

•  Your boxed Intel

®

 Pentium

®

 4 LGA775 processor package should  

come with installation instructions for the CPU, heatsink, and the 

retention mechanism. If the instructions in this section do not match  

the CPU documentation, follow the latter.

•  Check your motherboard to make sure that the PnP cap is on the 

CPU socket and the socket contacts are not bent. Contact your 

retailer immediately if the PnP cap is missing, or if you see any 

damage to the PnP cap/socket contacts/motherboard components. 

ASUS will shoulder the cost of repair only if the damage is shipment/

transit-related.

•  Keep the cap after installing the motherboard. ASUS will process 

Return Merchandise Authorization (RMA) requests only if the 

motherboard comes with the cap on the LGA775 socket.

•  The product warranty does not cover damage to the socket 

contacts resulting from incorrect CPU installation/removal, or 

misplacement/loss/incorrect removal of the PnP cap.

2.5.1  Installing the CPU

Before installing the CPU, make sure that the socket box is facing 

towards you and the load lever is on your left.

To install a CPU:

1.  Locate the CPU socket on the motherboard.

To prevent damage to the 

socket pins, do not remove 

the PnP cap unless you are 

installing a CPU.

2.  Press the load lever with your 

thumb (A), then move it to the 

left (B) until it is released from 

the retention tab.

A

B

Load lever

Retention tab

R

P5L13L

P5L13L CPU Socket 775

Summary of Contents for T3-P5945GC - T Series - 0 MB RAM
















































































Reviews: