Atag WV6111LM, Instructions For Use And Installation

making holes in accordance with the diagram shown in 
(fi g. 1). To fi t the appliance correctly, align the front panel of 
the cooker hood with the cabinet door and adjust spacer 

L

using screws 

P

 (fi g. 2A), then ensure the appliance meets the 

cabinet at the rear. 

• 

Extraction through an outside wall

The appliance expels the fumes through an outside wall or 
a duct. It is necessary to buy a telescopic pipe in accordance 
with the standards in use (infl ammable)  and connect it to 
fl ange 

B

 (Fig 3).

• 

Recirculation

To transform the cooker hood from the extraction version 
to the re circulating one ask your supplier for an activated 
carbon fi lter.  
The fi lter must be fi tted to the extracting group cooker hood 
in the centre of the fan grille by twisting it by 90 degrees until 
it is gripped securely (Fig 6). For this operation remove the 
anti-grease fi lter(s) 

G

 (Fig 5). The clean air is returned into the 

room through a connecting tube passing inside the cupboard 
and connected to the ring 

B

 (fi g 4).

USE AND MAINTENANCE

•

We recommend that the cooker hood is switched on before 

any food is cooked. We also recommend that the appliance is 
left running for 15 minutes after the food is cooked, in order 
to thoroughly eliminate all contaminated air.
The eff ective performance of the cooker hood depends on 
constant maintenance; the anti-grease fi lter and the active 
carbon fi lter both require special attention.

• The anti-grease fi lter

 is used to trap any grease particles 

suspended in the air, therefore is subject to saturation (the 
time it takes for the fi lter to become saturated depends on 
the way in which the appliance is used).
- To prevent potential fi re hazards, the anti-grease fi lters 
should be washed a minimum of every 2 months (it is 
possible to use the dishwasher for this task).
- After a few washes, the colour of the fi lters may change. 
This does not mean they have to be replaced.
If the replacement and washing instructions are not followed, 
the anti-grease fi lters may present a fi re hazard.

• The active carbon fi lters

 are used to purify the air which 

is released back into the room. The fi lters are not washable 
or re-usable and must be replaced at least once every four 
months. 
The active carbon fi lter saturation level depends on the 
frequency with which the appliance is used, the type of 
cooking performed and the regularity with which the anti-
grease fi lters are cleaned.
• Clean the cooker hood frequently, both inside and outside, 
using a cloth which has been dampened with denatured 
alcohol or neutral, 

non

-abrasive liquid detergents.

• The light on the cooker hood is designed for use during 
cooking and not for general room illumination. Extended 
use of the light reduces the average duration of the bulb.

• Replacing halogen light bulbs (Fig. 7).

To replace the halogen light bulbs 

B

, remove the glass pane 

C

 using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution:

 do not touch the light bulb with bare hands.

• Commands: 

(Fig.2B)

Push-button A 

= on/off  lights switch

Push-button B 

= on/off  cooker hood switch.  The appliance 

switches on at speed level 1,  If the cooker hood is on depress 
the push-button for 2 sec. to switch off  the cooker hood.  If 

the cooker hood is at speed level 1 it will not be necessary 
to depress the push-button to switch the cooker hood off .  
Decreases the motor speed. 

Display C 

= indicates the motor speed level selected and 

activates the timer. 

Push-button D 

= switches on the cooker hood.  Increases the 

motor speed.  Touching the key at 3rd speed, the intensive 
function runs for 10’, then the appliance go back to work at the 
original speed. During this function the display blinks.

Key E 

= The Timer times the functions on activation for 15 

minutes, after which they are switched off . The Timer is deac-
tivated by re-pressing 

Key E

. When the Timer is activated the 

decimal point must fl ash on the display. The Timer cannot be 
activated if the intensive speed is functioning.

The 

“clean air” 

function is activated by pressing key 

E

 for 2 

seconds when the appliance is switched off . This switches the 
motor on for 10 minutes every hour at the fi rst speed. During 
functioning a rotary movement of the peripheral segments 
must be visualised on the display. When this time has passed 
the motor switches off  and the fi xed letter 

“C”

 must be visu-

alised on the display until the motor re-starts after 50 minutes 
for another 10 minutes and so on. Press any key apart from 
the light keys to return to normal functioning. Press key 

E

 to 

deactivate the function.

• Active carbon/grease fi lter saturation:

- When display item 

C

 fl ashes, at a speed where it alternates 

with the letter 

F 

(e.g. 1 and 

F

), the 

grease 

fi lters must be 

washed.
- When display item 

C

 fl ashes, at a speed where it alternates 

with the letter 

A 

(e.g. 1 and 

A

), the 

carbon 

fi lters must be 

replaced.
After the clean filter has been positioned correctly, the 
electronic memory must be reset by pressing button 

A

 for 

approximately 

5 seconds

, until the indication 

F

 or 

A

 shown 

on the display 

C

 stops fl ashing.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR 
EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE 
WARNINGS.

- 11 -