12
On / Off switch
Do not use any device where the switch can not be switched
on and off. Damaged switches must be repaired or replaced
immediately by the customer service.
Switch on
Press the green button I .
Switch off
Press the red button 0 .
Restart protection in case of power
failure
In case of a power failure, the device switches off automatically
(zero-voltage initiator). To restart, press the green button again.
Motor protection
The motor is equipped with a safety switch and switches off
automatically when overloaded. After a cooling-down break
(approx. 5 min), the motor may be restarted. Press the
1.
reset button (motor protection)
2.
green button I to restart.
Electrical mains supply impedance
When conditions in the electrical mains supply are un-favourable,
voltage reductions for short periods can occur during the process
of turning on the equipment, which can adversely affect other
equipment (e.g., the flickering of a lamp).
No breakdowns are to be expected if the maximum, electrical
mains supply impedances given in the table are met.
Power consumption P1 (W)
Electrical mains supply
impedance Zmax (W)
2300 0,24
2500 0,24
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
g
g
a
a
r
r
d
d
e
e
n
n
s
s
h
h
r
r
e
e
d
d
d
d
e
e
r
r
Choose a working position alongside the equipment or be-
hind it. Never stand near the ejection opening.
Longer material that is protruding from the device could
spring back when it is drawn in by the blades! Observe safety
distance!
Never reach into the filling or ejection opening.
Keep your face and body away from the filling opening.
Never place hands, other parts of the body or clothing into the
filler funnel, ejection channel or in the vicinity of other moving
parts.
Check that no chopped residues are in the filling hopper be-
fore switching on the equipment.
Do not tip or tilt the machine when the motor is running.
When filling, be careful that no pieces of metal, stones, bottles
or other objects unintended for processing, enter the filling
hopper.
Immediately switch off the equipment and allow it to come to a
stop, if foreign objects enter the filling hopper or if the equip-
ment starts to make unusual noises or vibrates. Remove the
mains plug and carry out the following checks:
−
inspect for damage,
−
replace or repair damaged parts,
−
check the equipment and tighten loose parts.
You must not repair the equipment yourself if you are
unauthorized to do so.
What can I shred?
Yes:
•
organic household and garden waste
e. g. hedge and tree cuttings, dead flowers and vegetable
kitchen waste.
No:
•
glass, metal, plastic, plastic bags, stones, cloth, roots with
soil, food left-overs, fish or meat.
Special tips on shredding:
¾
Branches, twigs and wood should be broken down immedi-
ately after they have been cut.
−
Material of this kinds gets very hard when it is dry, and the
maximum allowed branch diameter to be processed has to
be reduced.
¾
Remove any side shoots from branches with a large number
of twigs.
¾
How to shred garden and kitchen waste with hight water con-
tent and a tendency to clog
−
to prevent the machine from clogging, alternate waste with
wood containing material.
¾
Do not allow the shredded material to pile up too high in the
area of the ejection opening. This can lead to shredded mate-
rial blocking the ejection channel, and backing up to the filler
opening.
¾
Clean out the filler opening and ejection channel thoroughly if
the machine becomes blocked. Before doing this, switch the
motor off and disconnect the machine from the mains power
supply.
¾
Please do not exceed the maximum branch diameter speci-
fied (cutting fresh wood) for your appliance (
∅
see p. 15).
Depending on the wood’s nature and freshness the maximum
branch diameter the machine can process may be smaller.
Reset button
(motor protection)
ON OFF
Summary of Contents for BIOQUICK 2500
Page 126: ...125 ...
