Technical Manual & Parts Lists
11
Control Box Operation
Main Control Box:
The front of the main control box has an Auto/Manual Switch, a Manual Ruffle
Pushbutton, a Panel/Frame switch, an Unwinder Reverse Switch, a Fuse Holder, and 2
banks of 6 Thumbwheels. On the back is the power entry socket and an on/off switch. Be
sure the on/off switch is always on.
Note: The on/off switch only switches one line and does not make the box
safe to work on. Always disconnect the main power cord before servicing the
control box.
In Panel mode the Auto/Manual Switch turns on the
automatic ruffling cycles for the corners. When this switch is
in Manual the ruffling is disabled and the machine will only
sew, trim, and foot lift. In Frames mode the Auto position
allows the frame to be sewn without stopping by holding
down the sew foot switch until the cycle is complete. When
the switch is in the Manual position the machine will stop at
the beginning and end of each ruffle cycle and the foot switch
must be released and pressed again to continue the cycle.
The Manual Ruffle pushbutton turns on one ruffle
cycle and is also the Reset button for the automatic cycle.
Pushing this button once will turn on the ruffle cycle for one
ruffle. Pushing it a second time will reset the automatic
program and cause the ruffle hardware to reset and go to its
"Home" position. Use this button to reset the ruffler after
adjusting the ruffle size.
The Panels / Frames switch selects the operation mode. In the Panels mode the machine will
detect the edges of a panel being sewn to the gusset and stop at each corner. In Frames mode no panel is
used. The machine will sew for a specified preset distance, stop and make ruffles, and sew again until a
four sided "frame" has been created.
The Unwinder Reverse switch controls the direction of the Unwinder reel. Use to set the proper
direction depending on how the gusset material is wound. The Unwinder will run whenever the Treadle
is not in the neutral position (either sewing or healed back) and the Loop Eye is seeing the gusset
material.
The Fuse Holder fuses the entire machine. Replace the fuse with a 5A Slo Blow 250v as
necessary.
Summary of Contents for 1335MDS
