Technical Manual & Parts Lists
15
Adjusting the Edge Guide
The edge guide located on the
front of the table should be set so its left
edge aligns with the right edge of the
gusset. This is the guide for the right
edge of the panel.
Sewing the Panel
Heal back the treadle or step on
the foot lift pedal to raise the presser
foot. Swing in the stripper blade and the
folder/ruffler assembly. Be sure the
sensor at the back of the swing-out
bracket is lit indicating that the bracket
is all the way in to the detent. Pull the
gusset through the folder, under the presser foot and under the puller. Load the panel
under the gusset with the center of the short side even with the needle and the edge of
the panel against the edge guide. Lower the presser foot. Be sure the Auto/ Manual switch
is in its Auto position (up).
Sew the panel to the corner being sure not to get your hands in the way of the
electric eye mounted under the table which must "see" the edge of the panel as it nears
the presser foot. The machine will stop automatically at the corner. Go to neutral treadle
as you position your hands for turning. Place your right hand on the panel near the
presser foot and your left hand about 1 foot to the left on the panel. Treadle forward and
allow the machine to make the first ruffle sewing straight. Begin to rotate the panel as the
rest of the ruffles are formed. Try to turn an equal amount with each ruffle so that when
the ruffles are complete the panel has turned 90 degrees and the right edge of the panel
is resting against the left edge of the edge guide. The ruffles can be made one at a time
by going to neutral treadle between each ruffle. Complete all four corners.
Adjusting the Corner Ruffles
The ruffles should be set so the outer edge of the gusset lays flat for taping. A
typical ruffled gusset will have 3 or 4 large ruffles which butt against each other without
overlapping or gaps between them. Adjust Thumbwheels #5 and #6 and the ruffle size
knob to achieve the desired finish. Euro style gussets typically have 3 or 4 small ruffles
with extra stitches between them.
Finishing the Panel
After the last corner, sew the panel until the starting edge of the gusset is almost to
the presser foot. Stop and swing out the folder. Cut the gusset so that there is enough
overlap of gusset for finishing. Swing out the stripper blade. Fold the trailing edge of the
gusset under itself, lay it on top of the starting edge and oversew the two together. Heal
back and remove the panel.
Summary of Contents for 1335MDS
