background image

9. If compressed air is used in the food industry and more specifically for direct food contact, it

is recommended, for optimal safety, to use certified Class 0 compressors in combination
with appropriate filtration depending on the application. Please contact your customer center
for advice on specific filtration.

1.3

Safety precautions during installation

All responsibility for any damage or injury resulting from neglecting these precautions, or
non observance of the normal caution and care required for installation, operation,
maintenance and repair, even if not expressly stated, will be disclaimed by the
manufacturer.

Precautions during installation

1. The machine must only be lifted using suitable equipment in accordance with the applicable

safety regulations. Loose or pivoting parts must be securely fastened before lifting. It is
strictly forbidden to dwell or stay in the risk zone under a lifted load. Lifting acceleration and
deceleration must be kept within safe limits. Wear a safety helmet when working in the area
of overhead or lifting equipment.

2. The unit is designed for indoor use. If the unit is installed outdoors, special precautions must

be taken; consult your supplier.

3. In case the device is a compressor, place the machine where the ambient air is as cool and

clean as possible. If necessary, install a suction duct. Never obstruct the air inlet. Care must
be taken to minimize the entry of moisture at the inlet air.

4. Any blanking flanges, plugs, caps and desiccant bags must be removed before connecting

the pipes.

5. Air hoses must be of correct size and suitable for the working pressure. Never use frayed,

damaged or worn hoses. Distribution pipes and connections must be of the correct size and
suitable for the working pressure.

6. In case the device is a compressor, the aspirated air must be free of flammable fumes,

vapors and particles, e.g. paint solvents, that can lead to internal fire or explosion.

7. In case the device is a compressor, arrange the air intake so that loose clothing worn by

people cannot be drawn in.

8. Ensure that the discharge pipe from the compressor to the aftercooler or air net is free to

expand under heat and that it is not in contact with or close to flammable materials.

9. No external force may be exerted on the air outlet valve; the connected pipe must be free of

strain.

10. If remote control is installed, the machine must bear a clear sign stating: DANGER: This

machine is remotely controlled and may start without warning.
The operator has to make sure that the machine is stopped and depressurized and that the
electrical isolating switch is open, locked and labelled with a temporary warning before any
maintenance or repair. As a further safeguard, persons switching on or off remotely
controlled machines shall take adequate precautions to ensure that there is no one checking
or working on the machine. To this end, a suitable notice shall be affixed to the start
equipment.

11. Air-cooled machines must be installed in such a way that an adequate flow of cooling air is

available and that the exhausted air does not recirculate to the compressor air inlet or
cooling air inlet.

Instruction book

6

AIF999999

Summary of Contents for AIF999999

















































































Reviews: