D 10.18 7
Item Designation
Brief description
14
Starter / drive
engine OFF
For starting and shutting off the drive engine.
- On actuation, the starter is in operation
- Switch the running engine OFF by pressing the but-
ton again
m
Run the starter continuously for a maximum of 20 sec-
onds, then take a break for 1 minute!
A
All emergency stop buttons (on the operating panel and
the remote controls) must be pulled out when starting.
15
/
16
Drive lever
(traction)
For switching on the paver finisher functions and for continu-
ously regulating the road speed – forward or reverse.
Centre position: Engine in neutral; no travel drive;
- To swivel the drive lever out, release by pulling the
handle (16) up.
Depending on the position of the drive lever, the following
functions can be activated:
1st position:
- Conveyor and auger on.
2nd position:
- Screed motion (tamper/vibration) on; travel drive on;
increase speed until the stop is reached.
A
Use the preselector to set the maximum speed.
f
The vehicle speed cannot be reduced to "0" with the
preselector. The vehicle advances slightly with deflect-
ed drive lever, even if the travel drive preselector is set
to zero!
A
If the engine is started with the drive lever pivoted out,
the travel drive is inhibited.
To start the travel drive, first the drive lever must be re-
turned to the centre position.
A
When changing over between forwards and reverse
travel, the drive lever must remain briefly in neutral.
Summary of Contents for Dynapac F1800C
