Atlas Copco XRVS 1300 CD7 Instruction Manual Download

Page: 10 / 102

- 10 -

When operating in a dust-laden atmosphere, place
the unit so that dust is not carried towards it by the
wind. Operation in clean surroundings
considerably extends the intervals for cleaning
the air intake filters and the cores of the coolers.

Close the compressor air outlet valve before
connecting or disconnecting a hose. Ascertain
that a hose is fully depressurized before
disconnecting it. Before blowing compressed air
through a hose or air line, ensure that the open end
is held securely, so that it cannot whip and cause
injury.

The air line end connected to the outlet valve
must be safeguarded with a safety cable, attached
next to the valve.

No external force may be exerted on the air outlet
valves, e.g. by pulling on hoses or by installing
auxiliary equipment directly to a valve, e.g. a
water separator, a lubricator, etc. Do not step on
the air outlet valves.

Never move a unit when external lines or hoses
are connected to the outlet valves, to avoid
damage to valves, manifold and hoses.

Do not use compressed air from any type of
compressor, without taking extra measures, for
breathing purposes as this may result in injury or
death. For breathing air quality, the compressed
air must be adequately purified according to local
legislation and standards. Breathing air must
always be supplied at stable, suitable pressure.

Distribution pipework and air hoses must be of
correct diameter and suitable for the working
pressure. Never use frayed, damaged or
deteriorated hoses. Replace hoses and flexibles
before the lifetime expires. Use only the correct
type and size of hose end fittings and connections.

10 If the compressor is to be used for sand-blasting

or will be connected to a common compressed-air
system, fit an appropriate non-return valve (check
valve) between compressor outlet and the
connected sand-blasting or compressed-air
system. Observe the right mounting position/
direction.

11 Before removing the oil filler plug, ensure that the

pressure is released by opening an air outlet
valve.

12 Never remove a filler cap of the cooling water

system of a hot engine. Wait until the engine has
sufficiently cooled down.

13 Never refill fuel while the unit is running, unless

otherwise stated in the Atlas Copco Instruction
Book (AIB). Keep fuel away from hot parts such
as air outlet pipes or the engine exhaust. Do not
smoke when fuelling. When fuelling from an
automatic pump, an earthing cable should be
connected to the unit to discharge static
electricity. Never spill nor leave oil, fuel, coolant
or cleansing agent in or around the unit.

14 All doors shall be shut during operation so as not

to disturb the cooling air flow inside the
bodywork and/or render the silencing less
effective. A door should be kept open for a short
period only e.g. for inspection or adjustment.

15 Periodically carry out maintenance works

according to the maintenance schedule.

16 Stationary housing guards are provided on all

rotating or reciprocating parts not otherwise
protected and which may be hazardous to
personnel. Machinery shall never be put into
operation, when such guards have been removed,
before the guards are securely reinstalled.

17 Noise, even at reasonable levels, can cause

irritation and disturbance which, over a long
period of time, may cause severe injuries to the
nervous system of human beings. When the sound
pressure level, at any point where personnel
normally has to attend, is:

below 70 dB(A): no action needs to be taken,

above 70 dB(A): noise-protective devices
should be provided for people continuously
being present in the room,

below 85 dB(A): no action needs to be taken
for occasional visitors staying a limited time
only,

above 85 dB(A): room to be classified as a
noise-hazardous area and an obvious warning
shall be placed permanently at each entrance
to alert people entering the room, for even
relatively short times, about the need to wear
ear protectors,

above 95 dB(A): the warning(s) at the
entrance(s) shall be completed with the
recommendation that also occasional visitors
shall wear ear protectors,

above 105 dB(A): special ear protectors that
are adequate for this noise level and the
spectral composition of the noise shall be
provided and a special warning to that effect
shall be placed at each entrance.

18 The unit has parts, which may be accidentally

touched by personnel, of which the temperature
can be in exess of 80 °C (176 °F). The insulation
or safety guard, protecting these parts shall not be
removed before the parts have cooled down to
room temperature.

19 Never operate the unit in surroundings where

there is a possibility of taking in flammable or
toxic fumes.