background image

Warranty

This item has a one (1) year LIMITED warranty.

Atlas

®

 Automotive Equipment warrants the equipment to the 

original purchaser against defects in material or workmanship 

under normal use for a period of one year from the date of 

purchase. This warranty shall be limited to the replacement of 

materials or parts found defective, at the discretion of Atlas

®

 

Automotive Equipment and/or its authorized distributors. This limited one (1) year warranty 

DOES NOT apply to normal wear items (turntable jaws, belts, gauges, plastic jaw protectors, 

etc.). The limited one (1) year warranty does not include a labor warranty. Warranties do not 

apply to items that have been abused or misused.

Returned goods must be authorized to be returned (in writing) by Atlas

®

 Automotive Equipment 

and/or an authorized distributor and must be prepaid to a designated location. All returns may 

be subject to a 15% handling and restocking charge. Returned goods must be in like-new 

condition complete with warranty and original shipping papers.

Customer’s Responsibilities

•  Shall ensure that all air operated components are properly maintained

•  Shall ensure components are powered by well lubricated and moisture free compressed air 

(if a suspected defective part has not been properly lubricated it will not be covered under 

warranty)

•  Shall establish procedures to periodically maintain and inspect the equipment

•  Shall ensure that your wheel balancer is protected by a surge protector

•  Shall ensure that all equipment shall have adequate amperage service

 THIS WARRANTY IS EXCLUSIVE AND IS LIEU OF ALL OTHER WARRANTIES EXPRESSED OR 

IMPLIED INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY OR ANY IMPLIED 

WARRANTY OF FITNESS FROM A PARTICULAR PURPOSE, AND ALL SUCH IMPLIED WARRANTIES 

ARE EXPRESSLY EXCLUDED.

THE REMEDIES DESCRIBED ARE EXCLUSIVE AND IN NO EVENT SHALL THE MANUFACTURER, 

NOR ANY SALES AGENT OR OTHER COMPANY AFFILIATED WITH IT OR THEM, BE LIABLE 

FOR SPECIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR THE BREACH OF OR DELAY 

IN PERFORMANCE OF THIS WARRANTY. THIS INCLUDES, BUT IS NOT LIMITED TO, LOSS OF 

PROFIT, RENTAL OR SUBSTITUTE EQUIPMENT OR OTHER COMMERCIAL LOSS.

For warranty assistance, please call 866-898-2604.  Please have your invoice number ready so 

that we may be able to serve you better.  Warranty procedures cannot be initiated without an 

invoice number corresponding to the product serial number.

For further product and distributor information, please visit www.atlasautoequipment.com 

Summary of Contents for WB55





































Reviews: