Atlas IED AP-LEDIP Owner'S Manual Download

Page: 32 / 40

AP-S15HRIP / AP-S15IP / AP-S158IP

Owner’s Manual

– 32 –

AtlasIED.com

TELEPHONE: (800) 876-3333

SUPPORT@ATLASIED.COM

1601 JACK MCKAY BLVD.

ENNIS, TEXAS 75119 U.S.A.

System

Type

Networked AC Power Distribution Conditioner & Suppressor

Load Rating

Max Load 15A (1800W), Rated Load 12A (1440W)

Network Type

LAN, WEB User Interface (Note 1)

Panel

Activation Switch

Rocker with Security Bar

Circuit Breaker

15A Resettable Power Switch

Outlet On / Off Switches

Momentary Manual

AC Outlets

NEMA5-15R Switched (Programmable), Qty 8 (AP-S15HRIP Qty 5)

Note:

Outlet 8 Can Be Used to Activate a Fan Triggered by Temperature Range of On: 51° - 176°F / Off: 50° - 175°F

AC Mains IEC Power Socket

IEC NEMA 5-15P 15A 1800W with Power Cord Retainer

LAN Port

RJ45, Ethernet Port

Temp / Humidity Port

RJ14, Temperature, Humidity Probe, 2M, Probe Included

Display Port

RJ25, for AP-LEDIP Display for Voltage, Current, Temperature, Humidity, IP Address

Fault Report Port

3.5mm Jack, Fault Reporting Contact Closure, Normally Closed & Opens During Fault State, Cable Included

GPIO Fault Relay Port

Fault Relay Interface, Temperature, Humidity, Over & Under Voltage, Over Current, Surge, Cable Included

Indicators

Power On Indicator

Power Switch LED, Red

Outlet Status Indicators

Green, Qty 8 (AP-S15HRIP Qty 5)

Over Temperature Alarm Indicator

Red, Programmable Range 50° - 176°F , 10° - 80°C

Over Humidity Alarm Indicator

Red, Programmable Range 15 - 95%

Over Current / Voltage Alarm Indicator

Red, Programmable Range High - Voltage 100V - 140V, Under Voltage 80V- 120V

AC Fault Indicator

Red, Illuminates When Surge Protection is Damaged

AC Ground Indicator

Red, Illuminates When Earth Ground Is Bad

User Interface and Configuration

Web Interface

HTTP Protocol, XML Commands Available

Status

Voltage, Current, Temperature, Humidity, Spike Protection, Ground Fault, Outlet Status

Alarms

Voltage Hi / Lo, Current, System Temperature, Humidity, Fault Log

Scheduler

24 / 7, Group Schedule or Individual Outlet Schedule

Network

LAN Base, DHCP or Static IP, Individual Outlet Auto Ping Reset (Note 1)

Configuration

Outlet Renaming, Group Assignment, Sequence Delay Timing, Temperature Activated Outlet

Technical Data

Max AC Mains Current

12A, 1440W

Operating Voltage

100VAC - 132VAC

Power Consumption

8-Watts

Noise Attenuation RFI

10dB @ 10kHz / 40dB @ 100kHz / 100dB @ 10MHz

Min. Spike Clamping Voltage

460VRMS @ 3000A

Max. Spike Clamping Voltage

6000V, 1 nanosecond

Spike Clamping Voltage @ 100A

1250Vp for 20µs

Maximum Surge Current

6,500A

Energy Rating @ 2ms

600 Joules

Unit Operating Temperature Range

40º - 105ºF, 5º - 40.5ºC

Humidity Range

5% to 95% Relative Humidity

Fault Reporting

Web, GPIO Contact Closure (Closed During Normal Operation, Opens During Fault Condition), API-Commands

Summary of Contents for AP-LEDIP









































Search results

Summary of Contents for AP-LEDIP

Reviews:

Related manuals for AP-LEDIP

Brands by name

Popular brands

Atlas IED AP-LEDIP, Owner'S Manual

Search results

Summary of Contents for AP-LEDIP

Reviews:

Related manuals for AP-LEDIP

Brands by name

Popular brands