background image

Owner’s Manual

TSD-DA13 

1x3 Distribution Amplifier

 AtlasIED.com

 – 12 –

Specifications are subject to change without notice.

1601 Jack McKay Blvd. • Ennis, Texas 75119  U.S.A.

Telephone: 800.876.3333 • Fax: 800.765.3435

©2017 Atlas Sound L.P. The Atlas “Circle A”, Soundolier, and Atlas Sound are trademarks of Atlas Sound L.P. 

IED is a registered trademark of Innovative Electronic Designs LLC. All Rights Reserved. 

All other trademarks are the property of their respective owners. All specs are subject to change without notice. ATS003936 RevB 4/17

Limited Warranty

 

All products manufactured by AtlasIED are warranted to the original dealer/installer, industrial or 

commercial purchaser to be free from defects in material and workmanship and to be in compliance 

with our published specifications, if any. This warranty shall extend from the date of purchase for 

a period of three years on all AtlasIED products, including SOUNDOLIER brand, and ATLAS SOUND 

brand products except as follows: one year on electronics and control systems; one year on 

replacement parts; and one year on Musician Series stands and related accessories. Additionally, 

fuses and lamps carry no warranty. AtlasIED will solely at its discretion, replace at no charge or 

repair free of charge defective parts or products when the product has been applied and used in 

accordance with our published operation and installation instructions. We will not be responsible 

for defects caused by improper storage, misuse (including failure to provide reasonable and 

necessary maintenance), accident, abnormal atmospheres, water immersion, lightning discharge, 

or malfunctions when products have been modified or operated in excess of rated power, altered, 

serviced or installed in other than a workman like manner. The original sales invoice should be 

retained as evidence of purchase under the terms of this warranty. All warranty returns must comply 

with our returns policy set forth below. When products returned to AtlasIED do not qualify for repair 

or replacement under our warranty, repairs may be performed at prevailing costs for material and 

labor unless there is included with the returned product(s) a written request for an estimate of repair 

costs before any nonwarranty work is performed. In the event of replacement or upon completion of 

repairs, return shipment will be made with the transportation charges collect.

EXCEPT TO THE EXTENT THAT APPLICABLE LAW PREVENTS THE LIMITATION OF CONSEQUENTIAL 

DAMAGES FOR PERSONAL INJURY, ATLASIED SHALL NOT BE LIABLE IN TORT OR CONTRACT 

FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE ARISING OUT OF THE 

INSTALLATION, USE OR INABILITY TO USE THE PRODUCTS. THE ABOVE WARRANTY IS IN LIEU OF 

ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY 

AND FITNESS FOR A PARTICULAR PURPOSE.

AtlasIED does not assume, or does it authorize any other person to assume or extend on its behalf, 

any other warranty, obligation, or liability. This warranty gives you specific legal rights and you may 

have other rights which vary from state to state.

Service

Should your Atlas TSD require service, please contact the AtlasIED 

warranty department at 1-877-689-8055, ext. 277 to obtain an RA number.

AtlasIED Tech Support can be reached at 1-800-876-3333 or support.atlasied.com.

Visit our website at www.AtlasIED.com to see other Atlas products.

Summary of Contents for TSD-DA13













Reviews: