AtlasSound.com
2/4
1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.
TELEPHONE: (800) 876-3333
FAX (800) 765-3435
©2013 Atlas Sound L.P
. All rights reserved.
Atlas Sound and Strategy Series are trademarks of Atlas Sound L.P
. All other trademarks are the property of their respective owners. A
TS004763 RevA 11/13
Technical Specifications
Power Handling:
250 watts (45V) RMS
Sensitivity (1W / 1M):
102.5dB SPL
(75Hz – 14.5kHz
1
⁄
3
octave bands)
Frequency Response:
75Hz – 14.5kHz (±5dB)
Dispersion:
90˚ x 40˚
Nominal Impedance:
8
Ω
Minimum Impedance:
5.6
Ω
@ 9000Hz Nominal -6dB
Height:
24.91" (632.71mm)
Width:
29.57" (751.08mm)
Depth:
29.65" (753.11mm)
Shipping Weight:
100 lbs (45.4kg)
Driver Type:
1" HF & 15" LF
Architect & Engineer Specifications
Loudspeaker shall be Atlas Sound Model AH94-15-BSG or approved
equal.
Loudspeaker shall be a 2-way design incorporating an environment-
resistant housing.
Loudspeaker shall include a 15", horn loaded, cast frame woofer housed
in a 2296 in
3
(1.3 ft
3
) enclosure and an integral, concentrically mounted 1"
exit compression driver coupled to a constant directivity high frequency
horn. The three pole (18dB/octave) dividing network crossover frequency
shall be 1.4kHz. The dividing network shall include a poly switch
protection circuit for the high-frequency component.
The loudspeaker system shall be capable of providing a sound dispersion
angle of 90˚ horizontal by 40˚ vertical in the 2kHz octave band.
Rated power shall be 250 watts based on EIA Standard RS-426B*.
Enclosure shall be UV-resistant, steel reinforced, low pressure injection
molded fiberglass and shall include a 3 stage multiple mesh filter system
for weather and rodent resistance:
A. Large 20-gauge perforated aluminum screen on front mouth
assembly.
B. 100 x 100 weave stainless steel mesh between HF horn and HF
driver.
C. 100 x 100 weave stainless steel mesh over 15" woofer.
Sensitivity shall be 102.5dB SPL (75Hz to 17kHz
1
⁄
3
octave bands)
measured at a distance of 1 meter on axis with a 1 watt input.
Overall frequency response shall be 75Hz – 14.5kHz (±5dB).
The loudspeaker shall include a stamped and formed, 12-gauge stainless
steel mounting bracket assembly for surface mounting and three M8
drop forged eyebolts for suspension mounting.
The input section located on the bottom rear of the loudspeaker shall
include a 4 pole terminal block connector.
Nominal impedance shall be 8
Ω
.
Dimensions shall be: Height 24.91" (632.71mm)
Width 29.57" (751.08mm)
Depth 29.65" (753.11mm)
Weight 100 lbs (45.4kg)
* EIA test spectrum is applied for eight hours.
(This procedure provides a rigorous test of both thermal and
mechanical failure modes.)
14.21
29.65
28.33
29.57
22.58
24.91
29.65"
(753.11mm)
14.21"
(360.93mm)
28.33"
(719.58mm)
24.91"
(632.71mm)
22.58"
(573.53mm)
29.57"
(751.08mm)
