background image

Safety 

18

PV-15P

Safety

Read this chapter carefully and completely because it contains important 

information for the safety of the operator and the person in charge of maintenance.

The lift has been designed and built for lifting vehicles and 

making them stand above level in a closed area. Any other use is 

forbidden.

The manufacturer is not liable for possible damages to people, 

vehicles or objects resulting from an improper or unauthorized 

use of the lift.

For operator and people safety, a square space for a safety area at least 3 feet 

free away from the lift must be vacated during lifting and lowering. The lift must 

be operated only from the operator’s control site in this safety area.

Operator’s presence under the vehicle, during working, is only admitted when 

the vehicle is lifted and the safety lock is engaged.

Never use the lift when safety devices are off-line. People, the 

lift and the vehicles lifted can be seriously damaged if these 

instructions are not followed.

6.1 General 

Warnings

The operator and the person in charge of maintenance must follow accident-

prevention laws and rules in force in the country where the lift is installed.

They also must carry out the following:

•  Neither remove nor disconnect hydraulic, electric, or other safety devices;
•  Carefully follow the safety indications applied on the machine and included 

in the manual;

•  Observe the safety area during lifting;
•  Be sure the motor of the vehicle is off, the gear engaged, and the parking 

brake put on;

Summary of Contents for PV-15PX






















































Reviews: