manualshive.com logo in svg

Atlas WB41, Quick Start Manual

The Atlas WB41 Quick Start Manual is a must-have for anyone using this top-of-the-line product. Find and download the comprehensive manual for free from our website. Get step-by-step instructions and valuable tips to make the most of your Atlas WB41.

Share
Download
background image

9 

 

STEP 7:

 

Press “ENTER” 

 

STEP 8:

 

The display will read “

Add 0

”. Lower the hood and spin the wheel. 

 
 
 
 
 
 
 
 
 
 
 

STEP 9:

 

When the cycle is finished and the tire stops, the display will read “

3.50 Add

”

 

(100 grams)

. Rotate the wheel until all the inside weight indicators are fully lighted. 

Apply the 

3.5 ounce (100 gram)

 calibration weight on the inside edge of the wheel at 

the 12 o’ clock position. Lower the hood and spin the wheel. 

 
 
 
 
 
 
 
 
 
 
 

STEP 10:

 

When the cycle is finished, the display will read “

Add 3.50

” 

(100 grams)

. 

Remove the calibration weight from the inside edge of the wheel. 
Rotate the wheel until all the outside weight indicators are fully lighted. 
Apply the 

3.5 ounce (100 gram)

 calibration weight to the outside edge of the wheel 

at the 12 o’ clock position. Lower the hood and spin the wheel. 

 
 
 
 
 
 
 
 
 
 

Summary of Contents for WB41











Reviews:

No comments

Related manuals for WB41

Brands by name

Popular brands

Load more brands