manualshive.com logo in svg

Atlas WBT-210, Quick Start Manual

Looking to get started with the Atlas WBT-210? Look no further! Download your free Quick Start Manual from our website for a hassle-free setup. This comprehensive manual will walk you through the product features and ensure a smooth experience. Get the most out of your Atlas WBT-210 today!

Share
Download
background image

5 

 

 

Switching from grams to ounces 

 

STEP 1:

 

Press “

MENU

” to access the menu functions. 

 

STEP 2:

 

Use the “

-/+

” keys to scroll through the menu functions until “

SET UP

” is displayed. 

 

STEP 3:

 

Press “

ENTER

” 

 

STEP 4:

 

Use the “

-/+

” keys to scroll through the set up functions until “

U

” is displayed. 

 

STEP 5:

 

Press “

ENTER

” 

 

STEP 6:

 

Use the “

-/+

” keys to select ounces or grams. Press “

ENTER

” to confirm the setting. 

 

STEP 7:

 

Press “

MENU

” to exit. Press “

STOP

” to return to the regular balancing mode. 

 

NOTE: 

Refer to the “Installation and Service Manual” for additional key functions 

and instructions. 

Summary of Contents for WBT-210


















Reviews:

No comments

Related manuals for WBT-210

Brands by name

Popular brands

Load more brands