Atmel ATEVK525 Hardware User'S Manual Download

Page: 28 / 30

Complete Schematics

7-28

ATEVK525 Mass Storage Board for AVR

7740B–AVR–03/08

Note:

The rows with grey background color specify that the corresponding component is not
mounted by default (power protection circuit, NAND Flash socket...)

Table 7-1 .

Bill of Materials

Qtty

Schematic

Reference

Part Reference

Description

Case

CAPACITORS

1µF

Tantalum 1µF 16V capacitor

SMD 3216

C2, C8

4.7µF

Tantalum 4.7µF 16V capacitor

SMD 3216

C3, C6, C7

10nF

Ceramic multi-layer 10nF capacitor

SMD 0805

C4, C5

1nF

Ceramic multi-layer 1nF capacitor

SMD 0805

DIODES

HSMC-C170

Red LED “WRITE”

SMD 0805

HSMG-C170

Green LED “READ”

SMD 0805

HSML-C170

Orange LED “PWR_FAIL”

SMD 0805

CONNECTORS

J1, J3

M20-6102005

PC104 2x20-pin through-hole female press-fit stackable

connector

2.54mm pitch

FPS009-3001

Yamaichi SD/MMC Connector with manual eject

See DS

J2, J4

SIP13, 2.54mm pitch, socket for NAND Flash module

2.54mm pitch

CONFIGURATION

CP1, CP2

Configuration Pad

Enabled by default. Can be disabled cutting it.

N/A

SP1

Solder Pad

Disabled by default. Can be enabled with a solder drop.

N/A

TP1-TP10

Test Point

Solder or touch the testpoint with a probe

Circular pad

RESISTORS

R1, R11

47 KOhms

Resistor 0.1W 1% 47 KOhms

SMD 0805

R5, R7

47 KOhms

Resistor 0.1W 1% 47 KOhms

SMD 0805

R2, R3

820 Ohms

Resistor 0.1W 1% 820 Ohms

SMD 0805

R12

820 Ohms

Resistor 0.1W 1% 820 Ohms

SMD 0805

150 KOhms

Resistor 0.1W 1% 150 KOhms

SMD 0805

10 KOhms

Resistor 0.1W 1% 10 KOhms

SMD 0805

R8, R10

0 Ohms

Resistor 0 Ohms (strap)

SMD 0805

75 KOhms

Resistor 0.1W 1% 75KOhms

SMD 0805

INTEGRATED CIRCUITS

LM393M

Double comparator, open collector output

SO-8

LM385M3-1.2

Voltage reference 1.235V

SOT-23

MT29F2G008AACWP

256Mx8bits NAND Flash memory

TSSOP-48

Si2301BDS

P-Channel low Vgs & Rds(on) FET transistor

SOT-23

Summary of Contents for ATEVK525































Search results

Summary of Contents for ATEVK525

Reviews:

Related manuals for ATEVK525

Brands by name

Popular brands

Atmel ATEVK525, Hardware User'S Manual

Search results

Summary of Contents for ATEVK525

Reviews:

Related manuals for ATEVK525

Brands by name

Popular brands