background image

 

 

Error! Reference source not found.

 [ZigBit 900 MHz Wireless Modules] 

17 

3.7 

Antenna reference designs 

Multiple factors affect proper antenna match, hence, affecting the antenna pattern. The particular factors are the board 

material and thickness, shields, the material used for enclosure, the board neighborhood, and other components 

adjacent to antenna. Following guidelines need to be followed when designing the base board for the ZigBit. 

General Recommendations: 

 

Metal enclosure should not be used. Using low profile enclosure might also affect antenna tuning. 

 

Placing high profile components next to antenna should be avoided. 

 

Having holes/vias punched around the periphery of the board eliminates parasitic radiation from the board 

edges also distorting antenna pattern. 

 

ZigBit module should not be pla

ced next to consumer electronics which might interfere with ZigBit’s RF band 

frequency. 

The board design should prevent propagation of microwave field inside the board material. Electromagnetic waves of 

high frequency may penetrate the board thus making the edges of the board radiate, which may distort the antenna 

pattern. To eliminate this effect, metalized and grounded holes/vias must be placed around the board's edges. 

4. 

Section 4 

Figure 4-1.  Internal schematics.

  

RFonly_212B_Schem

atics_include first Page only

 

Handling Instructions 

The ZigBit Modules are fixed with an EMI Shield to ensure compliance to Emission and Immunity rules. This shield is 

galvanic and NOT air tight. So cleaning of the module with IPA / other similar agents is not advised. Humidity protection 

coating (conformal) will cause deviated RF behavior and coating material being trapped inside EMI Shield. So this 

should be avoided. For products requiring conformal coating, it is advised to suitably mask the ZigBit before applying 

the coating to rest of the ZigBit carrier board. To protect ZigBit from humidity, the housing of the product should ensure 

suitable Ingress Protection standards are complied with. 

The MS-147 connector should never be exposed to Varnish / similar conformal coating material which will affect 

electrical connection on the surfaces of connector. 

The in-built chip antenna has been tuned for the particular design 

4.1.1 

General recommendations 

 

Metal enclosure should not be used. Using low profile enclosure might also affect antenna tuning 

 

Placing high profile components next to antenna should be avoided 

 

Having holes/vias punched around the periphery of the board eliminates parasitic radiation from the board edges 
also distorting antenna pattern 

 

ZigBit module should not be placed next to consumer electronics which might interfere with ZigBit's RF frequency 
band 

Summary of Contents for ZIGBIT ATZB-RF-212B-0-CN























Reviews: