TROUBLESHOOTING
Your ceiling fan is designed to be longlasting with a strong body and well-tested
electronics. However if any problem arises, please refer to the guidelines shared. Please
contact a local electrician or service engineer if you need any help.
Problem
Cause
Solution
Fan does
Fuse down / MCB shut off
Check fuse of the MCB on the mains.
not start
Loose wire connection to
Check the wire connection
fan or to the switch on the
and restore the connection
panel
Fan still does not start
Please contact the service
number provided.
Regulator is connected to
It is recommended that the
the fan
regulator should not be
connected to this ceiling fan and
it is instead controlled using
the remote provided with it.
Fan making
Bearing inside the housing
This ceiling fan is designed to
noises
has problems
be longlasting. However, after
many years of use, the
bearing may wear off and may
need to be replaced.
Fan blades are not seated
Make sure the blades are
properly on the motor
properly fastened to the body.
Loose connection may cause
accidents.
Shackle kit rattling
Make sure that the screws and
nuts are securely fastened
along with washer provided.
Fan is wobbling Nut holding motor shaft
Securely fasten the nut and
and the down rod is loose
bolts along with washers as
per the instructions provided
in this manual.
Nut holding down rod and
Securely fasten the nut and
shackle kit is loose
bolts along with washers as
per the instructions provided
in this manual.
Screws in the shackle kit and
Securely fasten the nut and
the ceiling hook are loose
bolts along with washers as
per the instructions provided
in this manual.
Fan blades are not seated
A common mistake is fixing the
properly on the motor
blades in the reverse direction.
Please set it right, and
securely fasten the screws.
Fan blades are out of balance
Make sure that the blades are
not bent during cleaning. Also,
interchanging them helps
balance the blades.
CONTROLLING THE FAN’S SPEED WITHOUT THE REMOTE
Renesa Smart+ is a loT enabled smart fan that works with Amazon Alexa App/Echo and Google Home
App/Assistant it can also be controlled by Atomberg Application.The fan's main switch can be used to control
its speed. Turn the fan's switch OFF and ON repeatedly to set the fan to the desired speed. Delay between
toggling between the OFF and ON buttons should be approximately 1 second. If toggling is too fast or too
slow, it will not work. While toggling, the LEDs will glow to indicate the speed of the fan. Refer to the below
table to control the fan using the switch.
Remote key
Function
Description
LED status
1
Speed 1
Sets fan to speed 1
One LED will glow for 1 sec
2
Speed 2
Sets fan to speed 2
Two LED will glow for 1 sec
3
Speed 3
Sets fan to speed 3
Three LED will glow for 1 sec
4
Speed 4
Sets fan to speed 4
Four LED will glow for 1 sec
5
Speed 5
Sets fan to speed 5
Five LED will glow for 1 sec
B
Boost Speed
Sets Fan to boost Mode
All LEDs blink thrice
Timer
OFF Timer/
•Fan automatically
Timer 1-One LED blinks twice
Wakeup
switches OFF/ON after the
Timer 2-Two LEDs blink twice.
Timer
set hours (1,2,3 & 6 Hrs).
Timer 3-Three LEDs blink twice.
•No. of LEDs suggest no. of hrs set Timer 6-All LEDs blink twice.
•Press the Timer key 5 times,
Timer disable - Odd and Even
to disable Timer or once
LEDs blink in a pattern thrice.
after 6 Hr timer indication.
Sleep
Reduce
•Sleep mode works for
Sleep Mode Enable - Four LEDs
speed of
4 Hours. Speed is reduced
in square blink twice.
fan by 1
by 1 every 2 hours. Afterwards, the Sleep Disable - Odd and Even
every 2
fan continues to run on a reduced LEDs blink in a pattern thrice.
hours for
constant speed. Fan speed will not
4 hours
reduce below speed 1.
•If sleep mode is already set and sleep
key is pressed, it will disable sleep mode.
LED
LED ON/OFF
Turn ON/OFF LEDs.
All six LEDs will glow.
Note: Sleep mode will not work if the fan is OFF.
1 time
Previous
Fan runs at the
No indication
speed
same speed
2 times
Speed 1
Lowest speed 1
1 LED will glow and turn off
after 1 second.
3 times
Speed 2
Speed 2
2 LEDs will glow and turn off
after 1 second.
4 times
Speed 3
Medium speed 3
3 LEDs will glow and turn off
after 1 second.
5 times
Speed 4
Speed 4
4 LEDs will glow and turn off
after 1 second.
6 times
Speed 5
High speed 5
5 LEDs will glow and turn off
after 1 second.
7 times
Boost
Boost mode speed
6 LEDs will glow and turn off
after 1 second.
Toggle
(Turn switch
OFF and ON)
LED status
Descriptions
Speed
