manualshive.com logo in svg

Atronic JCM UBA-10-SS, User Manual

The Atronic JCM UBA-10-SS User Manual is readily available for free download from our website. This comprehensive manual provides step-by-step instructions for operating and troubleshooting your Atronic JCM UBA-10-SS product, ensuring a seamless user experience. Access the manual at 88.208.23.73:8080 and make the most of your product's features effortlessly.

Share
Download
background image

13

March 2006

Bill Acceptor - JCM UBA-10-SS

Bill Acceptor Tests

Description

The host machine provides test routines for bill

acceptor diagnostics.

Bills enabled

Use this menu to check which bills are enabled /

disabled by the host machine.

1. Open maindoor and press service button to enter

the Service Menu.

2. Enter "Service Menu / Diagnostics / Bill Acceptor /

Bills Enabled". A list with bill values, currency, code

and state is displayed.

Validator Test With Stacking

Use this menu to test bill acceptance with stacking.

Make sure to have hopper drawer keys and cashbox

keys at hand to retrieve bills after testing.

1. Open maindoor and press service button to enter

the Service Menu.

2. Enter "Service Menu / Diagnostics / Bill Acceptor /

Validator Test With Stacking".

3. Insert bills and check acceptance and stacking.

Validator Test Without Stacking

Use this menu to test bill acceptance without

stacking. After validation the bill is rejected.

1. Open maindoor and press service button to enter

the Service Menu.

2. Enter "Service Menu / Diagnostics / Bill Acceptor /

Validator Test Without Stacking".

3. Insert bills and check acceptance.

T

ROUBLESHOOTING

Note

:

Depending on game software

version the layout of the

menus may vary.

Summary of Contents for JCM UBA-10-SS















Reviews:

No comments

Related manuals for JCM UBA-10-SS

JCM GLOBAL RDM-100 Series Integration Manual preview
RDM-100 Series
Brand: JCM GLOBAL Pages: 50

Brands by name

Popular brands

Load more brands