background image

CC186 OR CC186/2 STAND-ALONE AND SYSTEM CLOCK                               

REV 05/16/01

APPLIED TECHNICAL SYSTEMS

PAGE 6

WWW.ATS-USA.COM

TECHNICAL SUPPORT

For questions concerning installation and operation of this product, contact our factory at:

PHONE (800) 444-7161

or

FAX (318) 797-4864

SERVICE POLICY

It is recommended that all service for this product be done by the factory or by a factory
authorized service representative.  Applied Technical Systems will provide ongoing service
support in and out of warranty.  Send your repairs to:

APPLIED TECHNICAL SYSTEMS

849 KING PLACE

SHREVEPORT, LA  71115

APPLIED TECHNICAL SYSTEMS

WARRANTY POLICY

ATS warrants its products to be free of defects in material and workmanship
for a period of 24 months from the date of purchase.  ATS will repair or
replace any product returned to its authorized factory service center within
the warranty period so long as there is no evidence that the product has
been abused, misused, damaged by lightning, overloads of any kind or
water, or altered in any way.

Products returned for warranty must be returned with freight prepaid.  ATS
will pay normal freight charges to return the product to the customer.
Special premium freight requested by the customer will be charged to the
customer.

ATS disclaims any warranties expressed or implied, including
merchantability and/or fitness for a particular purpose.  In no event shall
ATS be held liable for incidental or consequential damages.

Summary of Contents for CC186








Reviews: