background image

7

 
 
 

 
 

CAUTION

The symbols shown are internationally accepted symbols that warn of potentional 
hazards of electrical products. The lightning flash with arrowpoint in an equilateral 
triangle means that there are dangerous voltages present within the unit. The 
exclamation point in an equilateral triangle indicates that it is necessary for the user 
to refer to the users manual.

These symbols warn that there are no user serviceable parts inside the unit. Do 
not open the unit. Do not attempt to service the unit yourself. Refer all servicing to 
qualified personnel. Opening the chassis for any reason will void the manufacturers 
warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off 
immediately and take it to a dealer for service. Disconnect the unit during storms to 
prevent damage.

EC DECLARATION OF CONFORMITY

This product conforms to all the essential requirements and 
further relevant specifications described in following directives:  
2004/108/EC (EMC) and  2006/95/EC (LVD)

WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)

The WEEE marking indicates that this product should not be 
disposed with regular houshold waste at the end of its working 
life. This regulation is created to prevent any possible harm to the 
environment or human health. 

This product is developed and manufactured with high quality 
materials and components which can be recycled and/or reused. 
Please dispose this product to your local collection point or 
recycling centre for electrical and electronic waste. This will make 
to sure that it will be recycled on an environmentally friendly 
manner, and will help to protect the environment in which we 
all live. 

Summary of Contents for APT20













Reviews: