AUDAC SX408A User Manual & Installation Manual Download | Manualshive

Page: 10 / 16

background image

9

Balanced:

Unbalanced:

Red

Shield

Tip

Sleeve

6) Satellite output connections

On these euro terminal output connections is the amplified output signal present with a frequency
above 120Hz. Connect these to the satellite speakers.

A total of 4 speakers with an impedance of 8 Ohm can be connected to these output connections.
The total impedance load should not be lower than 4 Ohms.

«
...
8
9
10
11
12
...
»

Summary of Contents for SX408A

















Reviews:

No comments

Related manuals for SX408A

Brand: JBL Pages: 8

Brand: Rampage Pages: 6

In-Ceiling Subwoofer System C-10SW

Brand: OEM Pages: 2

XS-GTX100LW Marketing

Brand: Sony Pages: 2

Brand: Sony Pages: 2

XS-GTX120L - Mobile Stereo Speakers

Brand: Sony Pages: 2

Brand: Sony Pages: 2

XS-GTX100LW - Gtx 10" Sub Woofer

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 4

Brand: Sony Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands