PROFESSIONAL SERIES SPECIFICATIONS
Page 1
Page 4
PROFESSIONAL POWER AMPLIFIER
PROFESSIONAL POWER AMPLIFIER
OVERVIEW
For years, our engineers worked hard at R&D one kind of clever and honest amplifiers.
PAMP2 series is the smart series which use LCD display to illustrate all the functions and
performance of the amplifiers. They tell you clearly what the amplifiers are doing by LCD
display. Integrated different diagrams, our PAMP1 series can meet the different requirements
from different markets. Simple and easy control make the amplifiers become the first choice in
professional audio field.
ATTENTION
WARNING - using electric product, basic precautions should always be followed, including the
following:
(1)
Read all the SAFETY INSTRUCTIONS before using the product
(2)
To reduce the risk of injury, close supervision is necessary when the product is used
near children
(3)
Do not use this product near water-for example, near a bathtub, washbowl, kitchen
sink, in a wet basement or near a swimming pool or the like.
(4)
This product is capable of producing sound levels that could cause permanent
hearing loss. DO NOT operate for a long period of time at high volume or at a level that is
uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an
audiologist.
(5)
This product should be located so that its location or position does not interfere with
its proper ventilation
(6)
This product should be located away from heat sources such as radiators, heat
registers or other products that produce heat
(7)
The product should be connected to a power supply only of the type described on the
operating instructions as marked on the product. Always ensure that a good quality mains lead
is used applicable for your country
(8)
If the mains fuse need be replaced, DISCONNECT THE PRODUCT FROM THE
MAINS SUPPLY. The fuse is above the mains IEC socket, and must be replaced with a fuse of
the type and rating stated on the rear panel. If a replacement fuse fails immediately, contact
your local service agent. DO NOT replace with a higher value
(9)
The power-supply cord of the product should be unplugged from the outlet when left
unused fro a long period of time. When unplugging the power-supply cord, DO NOT pull on the
cord, but grasp it in the plug.
(10)
Ensure the mains isolation switch is readily accessible when the product is in use
(11)
Care should be taken so that objects do not fall and liquids are not spilled into the
enclosure through openings.
(12)
The product should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Object have fallen, or liquid has been spilled into the product; or
C. The product has been exposed to rain; or
D. The product does not appear to operate normally or exhibits a marked change in
performance; or
E. The product has been dropped or the enclosure damaged.
(13)
DO NOT attempt to service the product beyond that described in the user
maintenance instructions. All other servicing should be referred to qualified service personnel.
(14)
WARNING-DO NOT place objects on the product' s power cord or place it in a
position where anyone could trip over, walk on or roll anything over it. DO NOT allow the
product to rest on or to be installed over power cords of any type. Improper installations of this
type create the possibility of fire hazard and / or personal injury.
Installation guide lines
DO NOT use these amplifiers in damp or high humidity environments.
Do not use outdoors or anywhere where liquids could fall or splash onto the amplifier.
Ensure the amp is adequately ventilated, with free airflow to the front and rear panels.
Keep away from other heat sources. If the amps are mounted in a rack with other amps,
ensure there is adequate cool air flow front and rear. Note that air is drawn in through
the back panel, and exhausted through the front panel.
NEVER cover the amplifiers , as they may overheat.
Our power amplifiers are designed to fit standard 19" racks, with a 2 U height and 17
depth. We recommend the use of rear rack supports, especially if the rack is to be
mobile. Use shake proof washers or thread lock adhesive to prevent mounting bolts
becoming loose in transit.
MODEL
PAMP1.2000.2
PAMP1.1000.2
Output Stereo 8 Ohm *
2x600 W
2x400 W
Output Stereo 4 Ohm *
2x930 W
2x620 W
Output Stereo 2 Ohm *
2x1440 W
2x960 W
Output Bridge 8 Ohm *
1.860 W
1240 W
Output Bridge 4 Ohm *
2880 W
1920 W
* Power at < 0,05% Thd
Frequency Response
Input Sensitivity
Maximum input level
Input impedance active balanced
Signal/Noise ratio A Weighted RMS
Crosstalk at rated output power 8
Ohm
Damping factor f=1 KHz o Ohm
Slew rate internal
Protection
Indicators
Cooling
Front panel controls
Rear panel controls
Connector
Power supply
Dimension (WxDxH) mm
Weight
20 Kg
17,5 Kg
Level A Ch - B Ch - Power switch
Stereo/Bridge/Parallel mode switch - 0,77V/1,0 V/ 1,4 V
input sesitivity switch - Ground/lift switch - Low Pass/High
Pass/By Pass cross-over switch
Bal XLR Input - Speak on
AC 115 V / 230 V 50-60 Hz
482 x 495 x 88 mm
20 Hz - 20 KHz +/- 0,5 dB
0,77 - 1,0 - 1,4 V
21 dBV / 9 V
20 K Ohm
> 100 dB
> 60 dB
> 1000
> 40 V / µS
Short circuit - Current limited DC fault AC line fuse -
Thermal cut off - Power up/down transients - Slow start
Power (Green) - Protect (Yellow) - Clip (Red) - Bridge
(Green)
Variable speed fan
SERIES
PAMP1.
PAMP1.
SERIES
