background image

Audio International, Inc.

                                                                   SDS-1001-101-x Installation Manual 

 

 
Document #540306, Rev IR, 04/2005

 

 

 Page 7 of 12 

3.4.6  Clearance and Separation Requirements 
 

When running cables, avoid sharp bends and placing cables near 
aircraft control cables.  Maintain a MINIMUM clearance of three (3) 
inches from any control cable.  If wiring is run parallel to 
combustible fluid or oxygen lines, maintain a separation of six (6) 
inches between the lines.   

 

3.5   Physical Characteristics 

 

3.5.1  Locate the SDS-1001-101-x away from heat sources, magnetic 

fields, direct sunlight, and areas with excessive dust and/or 
moisture.  The unit shall 

NOT

 be mounted to the skin of the aircraft.  

 

3.5.2  This unit is capable of sustained intended operation with no internal 

cooling fan air circulation, intake, or exhaust and no ventilation 
holes in the chassis.  Additionally, this unit does not require external 
direct air-cooling for proper operation.  Installation recommendation 
requires 1-inch spacing from other equipment, modules, and 
structures except the mounting surface for which the unit should be 
in direct contact. 

 
3.5.3 Mounting provisions are provided via four (4) 0.144-inch diameter 

mounting holes – two (2) on each side of unit on provided mounting 
flanges.  The unit shall be rigidly mounted to its location using the 
appropriate fastening hardware supplied by the installing agency. 

 

3.5.4  When mounting the unit to the aircraft’s frame, allow sufficient 

space for mating connectors.  Refer to Section 7.0 for unit 
dimensions and mounting hole sizes. 

 

Summary of Contents for SDS-1001-101-X














Reviews: