User's Manual
992
Document #: LTRT-10375
Mediant 500 MSBR
[SNMPTrapEnterpriseOid]
Defines the SNMP MIB OID for the Trap Enterprise.
The default is 1.3.6.1.4.1.5003.9.10.1.21.
Note:
For the parameter to take effect, a device reset is required.
The device automatically adds the device’s unique product
identifier number at the end of your OID.
[acUserInputAlarmDescription]
Defines the description of the input alarm.
[acUserInputAlarmSeverity]
Defines the severity of the input alarm.
[AlarmHistoryTableMaxSize]
Defines the maximum number of rows in the Alarm History table.
The parameter can be controlled by the Config Global Entry Limit
MIB (located in the Notification Log MIB).
The valid range is 50 to 1000. The default is 500.
Note:
For the parameter to take effect, a device reset is required.
[ActiveAlarmTableMaxSize]
Defines the maximum number of currently active alarms that can
be displayed in the Active Alarms table. When the table reaches
this user-defined maximum capacity (i.e., full), the device sends
the SNMP trap event, acActiveAlarmTableOverflow. If the table is
full and a new alarm is raised by the <device>, the new alarm is
not displayed in the table.
The valid range is 50 to 300. The default is 120.
For more information on the Active Alarms table, see Viewing
Active Alarms on page 849.
Note:
For the parameter to take effect, a <device> reset is required.
To clear the acActiveAlarmTableOverflow trap, you must reset
the device. The reset also deletes all the alarms in the Active
Alarms table.
configure system > snmp
settings > engine-id
[SNMPEngineIDString]
Defines the SNMP engine ID for SNMPv2/SNMPv3 agents. This
is used for authenticating a user attempting to access the SNMP
agent on the device.
The ID can be a string of up to 36 characters. The default is
00:00:00:00:00:00:00:00:00:00:00:00 (12 Hex octets characters).
The provided key must be set with 12 Hex values delimited by a
colon (":") in the format xx:xx:...:xx. For example,
00:11:22:33:44:55:66:77:88:99:aa:bb
Note:
For the parameter to take effect, a device reset is required.
Before setting the parameter, all SNMPv3 users must be
deleted; otherwise, the parameter setting is ignored.
If the supplied key does not pass validation of the 12 Hex
values input or it is set with the default value, the engine ID is
generated according to RFC 3411.
SNMP Trap Destination Parameters
(configure system > snmp trap destination)
Note:
Up to five SNMP trap managers can be defined.
SNMP Manager
[SNMPManagerIsUsed_x]
Determines the validity of the parameters (IP address and port
number) of the corresponding SNMP Manager used to receive
SNMP traps.
[0] (Check box cleared) = Disabled (default)
[1] (Check box selected) = Enabled
Summary of Contents for Mediant 500 MSBR
