Audiovox 128-7760 Installation Instructions Manual Download | Manualshive

Page: 1 / 16

background image

128-7760

1 of 16

1

Model AS 9076

Installation Manual

Remote Start Upgrade Module

Installation Instructions

This Unit Is Intended For Installation In Vehicles With

12 Volt Negative Ground Electrical Systems,

Gasoline or Diesel With True Tach Reference

And Automatic Transmissions Only.

Kit Contents

(1) -Control Module
(1) - Multi Pin Input/Output Harness
(1) - Six Pin Power Harness
(1) - Four Pin Auxiliary Harness
(1) - Four Pin I/O Harness
(1) - Control Switch / Programming Switch
(1) - Ring Terminal
(4) - 1/2" Long Screws
(1) - Pin Switch
(1) - Remote Start Warning Label
(1) - Literature Package

1
2
3
...
»

Summary of Contents for 128-7760

















Reviews:

No comments

Related manuals for 128-7760

Chromoflex Pro Series

Brand: Barthelme Pages: 6

Brand: Magicar Pages: 9

Brand: hager Pages: 4

Brand: One for All Pages: 2

24116 - 4 - Device Universal Remote

Brand: GE Pages: 16

Brand: WACO Pages: 28

Brand: KCI Pages: 20

ecoNET300 Series

Brand: KIPI Pages: 16

Brand: IC Dynamics Pages: 18

Brand: Spektrum Pages: 17

Brand: Cobra Pages: 12

Brand: Philips Pages: 2

Brand: Wonde Proud Pages: 3

Brand: Samsung Pages: 24

Brand: Samsung Pages: 13

Brand: Samsung Pages: 32

Brand: Samsung Pages: 12

Brand: Samsung Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands