background image

128-7827

1 of 20

1

The selectable features can be set manually as explained below, or with the RF feature programmer.
To set features using the RF programmer, follow the instructions packaged with the programmer.
Factory default settings are indicated by bold text.

Note :

 The method of manual override can either be selected to operate from the valet switch or operate as custom code.

Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
NOTE: Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.
Also, No data will be indicated if a feature is not available for a particular model.  The unit will enter the feature but no selection will be available.

RF Programmable Feature Bank 1 Is For Transmitter Programming See Transmitter Programming Guide.
RF Programmable Features Bank 2 Is Alarm Selectable Features:

Feature Selection

1 Chirp

2 Chirps

3 Chirps

4 Chirps

5 Chirps

6 Chirps

1st DoorL/UL

1 Sec.

3.5  Sec.

1 Sec L, Dbl. U/L

Dbl L, 1 Sec UL

Dbl L, Dbl UL

1 S l/350mS ul

2nd Accy Lock

Auto Lock On

Auto Lock Off

3rd Accy. UL

Auto UL Dr.

Auto UL All

Auto UL Off

`

4th Headlights

Not Available

5th Passive Locks

Not Available

6th Pass/Act Arm

Not Available

7th Siren/Horn

Not Available

8th Horn Chirp

10mS

16mS

30mS

40mS

50mS

9th O/R Method

Not Available

10th 2 Step U/L

On

Off

11th Chp Del Tx

On

Off

12th Vlot Sense/Hd Wire

Not Available

13th Trigger Circuits

Not Available

14th L/UL Poll

Not Available

15th Aux Ch 5 Sel

Pulse

Push & Hold

10  Sec

20  Sec

Latch On/Off

Hold 3/S For O/P

16th Aux Ch 6 Sel

Pulse

Push & Hold

10  Sec

20  Sec

Latch On/Off

Hold 3/S For O/P

17th Aux Ch 7 Sel

Pulse

Push & Hold

10  Sec

20  Sec

Latch On/Off

Hold 3/S For O/P

18th Trigger Delay

Not Available

When using the RF programmer, enter the program mode as follows:

Turn the ignition on.

Press and release valet switch 3 times;

turn ignition off then on.

Press and hold valet switch for 5 seconds.

Siren and or lights chirp/flash 2 times indicating access to RF feature program mode.

Model APS-687

Installation Manual

Summary of Contents for APS687 - Car Prestige Remote Start





















Reviews: