background image

128-8797a

1 of 20

The select

able features can be set manually as explained below

, or with the RF feature programmer

.

T

o

 set features using the RF programmer

, follow the instructions p

a

ckaged with the programmer

.

Factory default settings are indicated by bold text.

Note :

 The method of manual override can either be selected to operate from the valet switch or operate as custom code.

Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.

Note:

 Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.

Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no se

lection will be available.

RF Programmable Feature Bank 1 Is For T

ransmitter Programming See T

ransmitter Programming Guide.

RF Programmable Features Bank 2 Is Alarm Selectable Features:

Feature Selection

1 Chirp

2 Chirps

3 Chirps

4 Chirps

5 Chirps

6 Chirps

1st DoorL/UL

1 Sec.

3.5 

Sec.

1 Sec L, Dbl. U/L

Dbl L, 1 Sec UL

Dbl 

L, 

Dbl 

UL

l/350mS 

ul

2nd 

Accy Lock

Not Available

3rd 

Accy

. UL

Not Available

4th Headlights

Not Available

5th Passive Locks

Not Available

6th Pass/Act 

Arm

Not Available

7th Siren/Horn

Not Available

8th Horn Chirp

Not Available

9th O/R Method

Not Available

10th 2 S

tep U/L

Not Available

1

1th Chp Del 

Tx

Not Available

12th V

olt

age/Hd W

ire

Not Available

13th Trigger Circuits

Not Available

14th Lock/Unlock Poll

Not Available

15th 

Aux Ch 5 Sel

Not Available

16th 

Aux Ch 6 Sel

Not Available

17th 

Aux Ch 7 Sel

Not Available

18th Trigger Delay

Not Available

When using the RF programmer

, enter the program mode as follows:

Turn the ignition on.

Press and release valet switch 3 times.

Turn ignition off then on.

Press and hold valet switch for 5 seconds.

Siren and or lights chirp/flash 2 times indicating access to RF feature program mode.

Model APS-57C

Installation Manual

Rev A:  Add new URL 11/4/2011

Summary of Contents for Prestige Platinum APS-57C





















Reviews: