background image

128-8774c

1 of 24

Page 1

Model APS-997C

Owners Guide

2 Way LCD Vehicle Security 

& Remote Start System 

PATENTED:  www.voxxintl.com/company/patents

Rev b New Format 5/2013

Rev c New FCC Disclaimer 9/2016

Features and Options 

Pages 2-3

Arming Your System-Active 

Page 4

Protection While The System is Armed 

Page 5

Disarming The System 

Page 5

Intrusion Warning Signals 

Page 6

Valet Override, Programming & Safety Control Switch 

Page 7

Programming Custom Override Code 

Page 7

Eliminating the Normal Arm/Disarm Chirps 

Page 9

Remote Panic Operation 

Page 9

RF Sensor Selection 

Page 10

Pushbutton LED Receiver Safety Control Switch 

Page 11

Remote Starting The Vehicle 

Page 11

Automatic Start Timer Operation 

Page 12

Optional Device Channels 

Page 13

Turbo Timer Operation 

Page 14

Telematic Upgrade 

Page 14

Transceiver  Screen Icons And Indications 

Page 15

Two Way Remote Features and Functions 

Page 18

24 Hour Timed Start Setup, Operation, and Use 

Page 21

Temperature Start Mode Operation 

Page 21

Two Way Remote Function Program Chart 

Page 21

Functions At A Glance 

Page 22

Programming New Or Replacement Transmitters 

Page 23

Summary of Contents for Prestige Platinum APS-997C

























Reviews: