background image

PROCEDURE FOR CHANGER INSTALLATION  USING  MOUNTING
STUDS

Note:

Make sure the anti-vibration spring position has been changed and verified for the proper  angle mounting (as shown on page 4).

1

Determine mounting location. If unit is to be installed onto mounting studs located under carpet, lift carpet to expose metal chassis
and mark position of each stud as shown below in detail A and B.

2

Insert two hexagonal mounting bolts through underside of each bracket (detail A) and mount stud bracket in position using two
self-tapping screws into metal chassis. Hex bolt heads should be flush with underside of stud bracket.

3

Replace carpet over bracket studs (detail B), mark position of stud end of each bolt, and cut holes in carpet so bolts protrude through
carpet.

4

Proceed with unit mounting by positioning unit mounting brackets over protruding hex bolts as shown in details CD and E.  Secure
mounting brackets to bolts using hex lock nuts.

5

If mounting studs are  to be located directly on mounting surface with no carpet in between, mount  changer directly on studs as
illustrated below in details ACD and E.

  7

STUD BRACKET MOUNTING

ARRANGEMENT

(Detail A)

STUD BRACKET MOUNTING

UNDER A CARPET

(Detail B)

VERTICAL INSTALLATION

WITH STUD BRACKET

(Detail C)

SUSPENDED INSTALLATION

WITH STUD BRACKET

(Detail D)

HORIZONTAL INSTALLATION

WITH STUD BRACKET

(Detail E)

HEX BOLT (M6 x 15)

CARPET

SELF-TAPPING SCREWS
(M5 x 12)

STUD BRACKET

CHASSIS

STUD BRACKET

STUD BRACKET

STUD BRACKET

CHANGER MOUNTING
BRACKET

CHANGER MOUNTING
BRACKET

HEX NUT (M6)

HEX NUT (M6)

HEX NUT (M6)

STUD BRACKET

CHANGER MOUNTING
BRACKET

Summary of Contents for SP-11CDS









Reviews: