background image

MATERIALS INCLUDED IN THIS PACKAGE:

1) VOH-641 Video Monitor with out TV Tuner / VOH-642 Video Monitor with TV Tuner (1 pc)
2) Accessory Harness (P/N 8010730) (1 pc)
3) 12 Pin Power / Signal harness (P/N 112B2821) (1 pc)
4) 2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc)
5) RCA “Y” Adapter (1 Male to 2 Female) (P/N 0892165) (1 pc)
6) Hardware Package

#4 x 3/8” Screws (12 pcs)
#8 x 5/8” Self Drilling Screws (4 pcs)
#8 Washers (4 pcs)

7) Remote Control (P/N 1361612 supplied with VOH-642 only)
8) Protective Cover for External A / V Inputs (P/N 1023336)

-1-

3e

3

2

3

3a

3f

3d

3e

3c

3b

3

5

6

4

3c

CHOKE

TOOLS REQUIRED:

#2 Phillips Screwdriver
#1 Phillips Screwdriver
Utility or Razor Knife or Shears
Wire Strippers
Upholstery hook tool (for removal of panels as necessary)
Electrical Tape
Masking Tape
Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe)
Marker pen – to mark headliner
Scribe (to mark trim ring if used)
Misc. electrical connectors (to connect to vehicle power source).  Requirements will vary from
vehicle to vehicle)
Video tape (to verify system operation after installation)

3a

7

OPE N

AUTO

ON

OFF

1

3a

8

Summary of Contents for VOH-641













Reviews: