background image

57

USER'S MANUAL

By clicking on the icon       , the menu for 

the output channels filter settings will 

appear as per image to the side.

1.

 

Xover L/R Link:

 when activated, the 

  modifications applied to one of the 

  channels (right or left) will automatically 

  be applied also to the other one. To 

  activate it click on the blue flashing light.

2. 

Invert Phase:

 it provides the ability to 

  invert the phase of the channel under 

  examination by 180°. It can be activated 

  by selecting the green flashing light.

  This function can be useful to solve 

  alignment problems among the different filtered channels

3.

 

Filter Type:

 it enables the selection of the different types of filters that can be assigned to the channels. 

Full Range

Low Pass

High Pass

Band Pass

The bit One HD Virtuoso manages 13 crossovers, one 

for each output channel. Each filter allows the setting 

of the parameters related to the channel highlighted on 

the Channel Map The filters can be adjusted in normal 

or extended mode through an active POP UP for a more 

detailed adjustment, activating it using the button.

Remark: 

by activating the PASS THROUGH mode the

  Filter Settings menu will not be active.

4.

 

Filter Model: 

it enables the selection of the applicable type of filter

 

Butterworth

 (IIR)

 

Linkwitz

 (IIR)

 

Bessel 

(IIR)

 FIR 

(to be enabled during the Wizard 

see sec. 7.2.2

)

  When starting the software, the bit One HD Virtuoso offers the 

  Butterworth as a standard filter model. By changing the model to 

  Linkwitz or Bessel, the change will be made only to the channel 

  (mono) or channels (stereo - Xover Link activated) concerned.
  If a FIR type system configuration was set up, the PC software will 

  not allow to manage other types of filters. If you wish to switch to the 

  Butterworth / Linkwitz or Bessel, (IIR) filters, proceed by converting 

  the configuration file as suggested in 

sec. 8.2.1

.

WARNING:

 in this case pay utmost attention to the filter adjustment. Speakers have mechanical limits which must

 

not be exceeded and could lead to damage to the components.

6

8.7.1 

FILTER SETTINGS

2

8

3

4

5

6

1

7

8.7

FILTER SETTINGS / DELAY

8

Summary of Contents for bit One HD Virtuoso



























































































Reviews: