background image

7

USER'S MANUAL

3

2

1

 

1.

  PRE OUT low-level analog signal (4 Volt RMS) 

(see section 5.7.2)

 

  Ch1 - Ch2 - Ch3 - Ch4 - Ch5 - Ch6 - Ch7 - Ch8 - Ch9 - Ch10 - Ch11 - Ch12 - Ch13

 

  To connect the RCA cables going to the system’s amplifiers.

 

2.

  AD Link - OUT digital signal 

(see section 5.7.1)

  

S/PDIF standard digital signal (Ch1÷Ch13) to connect amplifiers provided with the specific AD Link input.

 

  AD LINK 1: 

S/PDIF standard digital signal (Ch1÷Ch8) to connect amplifiers provided with the specific AD Link input

 

  AD LINK 2: 

S/PDIF standard digital signal (Ch9÷Ch13) to connect amplifiers provided with the specific AD Link input

 

3.

  AC Link: 

Connection socket to control the amplifiers provided with AC Link connection 

(see section 5.7.1)

.

      AC LINK 1: 

Connection socket to control the amplifiers (Ch1÷Ch8) provided with AC Link connection.

      AC LINK 2: 

Connection socket to control the amplifiers (Ch9÷Ch13) provided with AC Link connection.

 

4.

 RVA 

(Remote Volume Aux): control signal output to connect to the master source AUX input, to enable the 

   “

AIS - Auto Input Switch

” function. 

(see 5.4.3 - 5.6.1; 8.3.5)

.

Remark: 

the Remote Out signal is available on the AC LINK 1 / AC LINK 2 connection plugs and is active to the 

  amplifiers supporting this function (Audison AV amplifiers with AV bit IN input).

RCA / Jack

stereo Adapter

Included

4.2

OUTPUT SIGNALS

4500 mm / 177.17 in.

4

Summary of Contents for bit One HD Virtuoso



























































































Reviews: