background image

1.

Never use a record with cracks or warps.

2.

Never use a record that is cracked or warped, as this may cause extreme wear and destruction of the needle.

3.

Never use unusual play methods such as scratching. This unit is not designed for such playback.

4.

Do not expose the unit to direct sunlight, high temperature or high humidity. This may cause warping or deformation. When holding the 
record, hold only the label or the outer edge.

5.

Do not touch the record groove. Dust and fingerprints may cause distortion of the sound. Care of the record

6.

Use a special record cleaner and cleaner solution (sold separately). Wipe the record cleaner in a circular motion along the record groove.

Accessories 

Includes 

45 rpm adapter

2x Stylus(one installed)

AC/DC power adapter

7-inch Turntable mat

User’s quick guide

User’s manual

• 3 speed turntable plays 33 1/3, 78,  and 45 rpm records;

• Auto stop function
• Supports Bluetooth Input
• Aux In 3.5mm audio input
• All-in-one LED control panel
• Built-in stereo speakers
• USB/TF card recording
• USB/TF card playback
• RCA stereo audio outputs

Introduction 

Instructions 

Before Start

Read 

the 

manual before using this product. Keep these instructions for future reference. 

About Records

About USB 

/

TF cards that can be used with this unit

1.

The file format that can be played by this unit is WAV/MP3 format (extension: .wav/.mp3) only. USB in FAT/FAT32 format only.

2.

This product is not compatible with USB hubs.

3.

When a large capacity USB flash drive or TF card is connected, it may take some time to load the file.

4.

Press and hold the Pause/Play/DEL button on the unit to erase the files stored in the USB flash drive/TF card one by one.

5.

It is recommended that you make a backup of your files beforehand to prevent them from being erased unexpectedly by pressing the 
Pause/Play button on the panel.

About Bluetooth

Main features

1.

The Bluetooth devices used in this unit use the same frequency band (2.4GHz) as wireless LAN devices (IEEE802.11b/g/n), so if they are 
used near each other, they may interfere with each other, resulting in reduced communication speed or connection failure. In this 
case, please use it as far away as possible (about 10m).

2.

We do not guarantee the connection with all Bluetooth devices.

3.

Also, depending on the conditions, it may take some time to connect.

Received a defective record player ?

Notice: 

The gap between the case and the spinning 
mechanism is for vibration-absorbing, it's 

common

ly 

used 

design for starter turntable, 

which

 could be 

considered 

being defective

 mistakenly

.

2

Summary of Contents for TE-2026











Reviews: