46
Configure the COMpact TS Module
If you have extended the PBX with one (or two) COMpact TS modules,
you will have 3 (or 6) switch relays and much more. These offer many
configuration options to you. The table on
view to you.
Use Door Functions
If you like to enable the door telephony and the door opener function,
the following settings are necessary or possible in COMset:
For the buttons the corresponding door terminal, the key determina-
tion door as well as the kind of contact have to be set.
Under Internal telephone numbers a door terminal has to be config-
ured.
Under Call distributions the assignment Door -> Subscriber has to
be set.
For the relays the operation modes Door terminal function, door
opener function and perhaps Floor light with the requested Duration
time have to be set.
For the case that nobody takes the door call, the visitor, in front of the
door, can also be connected to the answering machine. Under Internal
call forwarding from the door terminal the ringer rhythm used by the
answering machine has to be configured properly.
The door call can also be diverted to an external connection. The Exter-
nal call forwarding from the door terminal has to be used. The con-
figuration of this function is also possible via telephone (
To identify the visitor’s door bell button the signalization of the door
bell button number for individual subscribers can be enabled.
If a telephone should only be used for the door function, you can set it
as door terminal phone. This telephone will immediately be connected
to the assigned door right after the receiver has been picked up.
If door opening should not be possible with a certain telephone, you can
withdraw the authorization to open the door from this subscriber.
Advice for COMpact 4410 USB: Use for door functions a
COMpact TS Module in slot B. If you use a TS Module in slot
C the announcement/Music on Hold function of the audio
jack is not available.
Use the universal switching Relays
If a relay should be used as an universal switching relay, the following
settings are necessary in COMset:
For the relay the operation mode Universal mode has to be selected.
If the relay has to be switched configuration dependent, you have to
activate Turn on if configuration x is active and create the corre-
sponding configuration.
If the relay has to be switched on as soon as a certain internal sub-
scriber of the PBX is called, you have to activate Turn on if PC relay
subscriber is called and to select the PC relay subscriber as well as
the Duration time.
But you can also switch manually from an internal or external telephone
(remote switching,
). For the internal and
remote switching the authorization to switch to the relays has to be
assigned. For the remote switching the MSN/DDI for room monitoring
and external programming and the external password have to be
configured
.
Music Functions
The PBX has an input for external Music on Hold alternatively to the
internal Music on Hold stored in the PBX. You can connect e.g. a CD
player here. If the connected CD player should not to be powered-on all
the time, it can be activated by a relay as soon as it will be needed. You
have to configure the operation mode Music on Hold and the
requested Switching time for the relay in COMset.
If you want to change the internal Music on Hold, there is an alternative
to the external Music on Hold input. It is also possible to store another
music than the existing internal Music on Hold in the PBX (COMpact
4410 USB only). This can be done with COMtools Music on Hold (save
a song as wave file
1)
in the PBX) as well as via telephone (record a
song with the PBX on the external Music on Hold input) (
).
Use Alarm Functions
The alarm order of events:
왎
Alarm detection at the alarm input (contact closed longer than ½ a
second).
왎
The configurable alarm delay time is running (0-99 seconds).
왎
Non recurring start of the siren (for 1-99 seconds) and/or the alarm
indication light (for 1-99 minutes).
왎
Simultaneously the first alarm call run starts (Alarm calls to the
alarm subscribers):
첸
Calling the first alarm subscriber for 60 seconds. Internal alarm
subscribers are called with a special ringer rhythm (ISDN tele-
phones: See manual of your telephone).
첸
After taking the receiver, you will hear an alarm announcement
stored in the PBX (COMpact 4410 USB only;
) again and again. (COMpact 2206 USB: You will hear a
signal tone). The called party must acknowledge the alarm call
within 60 seconds by sending the DTMF number
0
(
).
첸
If the called party does not acknowledge the alarm call, the next
alarm subscriber will be called some seconds after finishing the
first call. And so on....
왎
If all alarm subscribers are called without receiving an acknowl-
edgement, the alarm run will be repeated after a configurable alarm
waiting period (0-99 seconds) has elapsed (you can configure 1-10
alarm runs).
왎
The alarm will be terminated (including siren and alarm indication
light), as soon as one of the alarm subscriber acknowledges the
alarm. If the alarm input has been configured to „active once“, it is
deactivated afterwards. If the alarm input has been configured to
„active repetitive“, it is activated again and a new alarm can be trig-
gered.
If the alarm function of the PBX has to be used the following settings are
necessary in COMset:
For the door key input the door key determination alarm as well as
kind of contact have to be configured. With the corresponding circuity
(e.g. output of an alarm system) an alarm can be activated.
To control a siren and/or a code light, a relay has to be set the operation
mode siren or code light with the requested duration timing.
You can enter up to four internal and external telephone numbers under
alarm subscribers 1-4. It is recommended for calling external alarm
subscribers to activate emergency call has priority.
Depending on how often and how long an alarm has to be signalled,
modify the settings for alarm cycles, alarm time delay as well as alarm
waiting period.
You may activate the alarm function now. But the alarm can also be
activated or deactivated by an internal or external telephone (
).
COMpact 4410 USB: The announcement has to be recorded by tele-
phone (
) or transferred with COMtools Music
on Hold into the PBX.
Configure the COMpact TS Module
☞
1. Standard Windows format for audio data
Summary of Contents for COMpact 2206 USB
Page 66: ...884250...
Page 67: ......
Page 68: ...884250 03 03 04 Save the Earth 100 recycled paper...
