Auriol 4-LD4868 Usage And Safety Instructions Download

Page: 17 / 74

- 15 -

Mounting the outdoor sensor

Two different mounting options are possible with the included sensor mount 42

42. The sensor can be placed on a flat

surface or mounted on a wall or ceiling.
Illustration A

Illustration A

Illustration A shows the three indentations that are on each side of the sensor. The sensor can easily be clipped into the
mount using these indentations.
Illustration B

Illustration B

Illustration B is a side view, which shows how the mount is attached behind the sensor.
Illustration C

Illustration C

Illustration C shows a front view of the sensor with the mount used as a ceiling mount.
Illustration D

Illustration D

Illustration D shows a front view of the sensor with the mount used as a stand.
Illustration E

Illustration E

Illustration E shows the controls and the battery compartment on the backside of the sensor.

Please note:

Please note: Always hang or stand the sensor upright.

Setup

Remove the protective film from the weather station and the outdoor sensor. Open the battery compartment of the
outdoor sensor

and insert the included batteries in the correct polarity. The LED indicator

will briefly light up and

the display will show the temperature. Close the battery compartment.
Open the battery compartment of the weather station

and insert the included batteries in the correct polarity. Close

the battery compartment. The weather symbol 1

1 blinks and the weather station receives the signal from the outdoor

sensor. This process may take several minutes to complete. If reception is successful, the selected channel

and the

current outdoor temperature

will appear. After successful reception of the signal for the outdoor sensor, the reception

of the DCF77 time signal will begin and the radio control indicator

will blink on the display next to the time. All buttons

except the

SNOOZE / LIGHT

button

are disabled during the reception process. If reception fails after 10 minutes,

please set the time manually. The weather station will reattempt reception at 04:00 and 05:00 and, if reception is
successful, will correct the set time.

Note: Please do not move the weather station or the sensor during the reception process.

If the reception attempt is successful, the radio control indicator

will appear permanently on the display and the

correct time, date, day of the week and the times of sunrise, sunset, moonrise and moonset will be set automatically.

DST

will appear on the display next to the radio control indicator

during daylight saving time.

Time zone adjustment

If you are in a country, in which the clock displays the wrong time even though it can receive the time signal, please use
the time zone adjustment to use your weather station in a time zone other than the standard time zone (UTC+1 = Central
European Time). Set the difference in hours (- 01 for example) to the desired time zone.
In normal time display mode, press and hold the MODE

MODE

MODE button 15

15 for 3 seconds. The time zone will blink and can be set

by pressing the -/ -button

or the

12/24

-button

. Press the

MODE

-button

, to confirm your setting.

Restart radio reception after changing this setting. Your weather station receives the DCF77 time signal but will show the
adjusted time (1 hour less for example).

Note:

Always hang or place the sensor in an upright orientation.

Reception problems

The DCF77 radio signal is transmitted from a location near Frankfurt am Main and can be received within a radius of
approximately 1500 km around Frankfurt am Main. However, there are some obstacles and sources of interference,
which may substantially hinder reception. If your weather station does not correctly receive the DCF77 radio signal,
please hang or place the weather station in a different location at your site. Please note that devices such as computers,
telephones, radios and televisions may cause electromagnetic radiation which can interfere with the DCF77 signal
reception. Other possible detriments to reception are: strong building insulation (metal building materials), nearby
mountains or atmospheric interference. It may also be necessary to replace the batteries.

Restarting radio signal reception

Manually restart the radio signal reception by pressing and holding the -/ -button

for 3 seconds.

Light

Briefly activate the backlight by pressing the

SNOOZE/LIGHT

-button

12/24-hour time format

Select the 12- or 24 hour time format by pressing the

+/12/24

-button

. AM will appear on the display in the