background image

31 

IMPORTANT SAFETY INSTRUCTIONS 

WARNING

:  In  order  to  reduce  the  risk  of  injury  to  any  and  all  persons,  READ  and  UNDERSTAND  the  following  important 

PRECATIONS and information before operating or allowing others to operate the elliptical exerciser 

 

The owner has the responsibility of ensuring that all users of the elliptical exerciser are adequately informed of all warnings 

           

and precautions 

 

This elliptical exerciser should not be used by, on, or near children, invalids, or disabled persons. 

 

This  elliptical  exerciser  must  only  be  used  as  described  in  the  manual.  Attachments  that  are  not  recommended  by  the 
manufacturer must not be used. 

 

Never  operate  the  elliptical  exerciser  with  the  air  openings  blocked,  Keep  the  air  openings  free  of  lint,  hair  and  the  like. 
Never  operate  the  elliptical  exerciser  on  a  soft  surface  such  as  a  bed  or  a  couch  where  the  air  openings  may  be  blocked.   
And never drop or insert any object into any opening. 

 

Place the elliptical exerciser n a level surface. To protect the floor and carpet from damage, place a mat under the elliptical 
exerciser. 

 

DO NOT uses or store the elliptical exerciser outdoors, in a garage or covered patio, keep the elliptical exerciser away from 
moisture and dust. The elliptical exerciser should be used indoors. Heat, moisture and dirt can adversely affect the operation 
of this elliptical exerciser. 

 

DO  NOT  operate  the  elliptical  exerciser  where  aerosol  products  are  being  used  or  where  medical  oxygen  is  being 
administered. Injuries to health may result from incorrect or excessive training. Instructions shall be giver in respect of every 
major exercise type for which the equipment is designed. 

 

The recommended minimum free space for access around the elliptical exerciser is 0.6m at each side and 0.3m at the rear of 
the elliptical exerciser. This is to allow for an emergency dismount and passage around the elliptical exerciser. 

 

Keep children under the age of 12 and pets away from the elliptical exerciser at all times. 

 

No person weighing over 136 KGS (300 LBS) should use this elliptical exerciser. 

 

NEVER allow more than one person on the elliptical exerciser at a time 

 

Wear appropriate clothing  when using the elliptical exerciser. DO not  wear loose clothing that could become caught in the 
elliptical  exerciser.  Appropriate  athletic  support  clothing  is  recommended  for  both  men  and  women.  Always  wear  athletic 
shoes intended for walking with a non-slip sole. NEVER use the elliptical exerciser with bare feet, while wearing stockings 
only or in sandals. 

 

The pulse monitor is not a medical device. Various factors, including the user’s movement, may affect the accuracy of pulse 
rate readings. The pulse monitor is intended only as an aid to exercise in determining heart rate trends in general. 

 

“WARNING! Heart rate monitoring systems may be inaccurate. Over exercising may result in serious injury or 
death. If you feel faint stop exercising immediately”. 

 

Do  not  attempt  to  raise  lower  or  move  the  elliptical  exerciser  until  it  is  properly  assembled,  (  See  ASSEMBLY 
INSTRUCTIONS.) You must be able to safely lift 100 pounds ( 46 KGS) in order to raise, lower or move the unit. 

 

Do not place object under the elliptical exerciser in an attempt to change the incline of the elliptical exerciser. 

 

Inspect and tighten all parts of the elliptical exerciser every three months. 

 

This elliptical is design “ for Consummer Use Only “, not for any commercial or institutional, rental use. 

 

Consult your physician before beginning your exercise program, incorrect of excessive training may cause the health injuries. 

 

Tool require to assemble for the unit please refer to the end of parts list. 

 

VST (variable stride length adjustment) refer to the page of how to operate the adjustor page 4 and 5 

 

Any of the adjustment devices that could interfere with the user's movement should not be left projecting. 

 

The equipment need tool to assembly , required tool Refer to the parts list with manual. 

 

The product is a dependent only for indoor use specified with Class HB standard. With braking system—Speed dependent. 

 

The elliptical exerciser contents. Fit with. Lower body, upper and combined total body. 

SAVE THESE INSTRUCTIONS

 

Keep Fit Hire      www.keepfithire.com 

Summary of Contents for V-950
































Reviews: