background image

Aussie BB Hire Series … Operation & Maintenance Manual 

Aussie Pumps 

June 2016 

AUSSIE ECO CLEAN BB100 SERIES OPERATING AND MAINTENANCE INSTRUCTIONS 

 

* * W A R N I N G * * 

AUSSIE SCUD SERIES HIGH PRESSURE WATER BLASTERS ARE DESIGNED FOR PROFESSIONAL OPERATORS ONLY 

 

IMPORTANT

 

INSTRUCT OPERATORS IN CARE AND USE OF THE MACHINE BEFORE USE! 

Contents 

Page 

Warranty ………………………………………………………………………………………………… 

Safety Precautions …………………………………………………………………………………….. 

Assembly & Use ……………………………………………………………………………………….. 

A.   Machine Preparation (initial set up)  ………………………………………………………. 

B.   Hose Connections ………………………………………………………………………….. 

C.   Before Starting Machine …………………………………………………………………... 

D.   Starting Machine ……………………………………………………………………………. 

E.   Stopping Machine …………………………………………………………………………... 

Care & Maintenance ………………………………………………………………………………….. 

Troubleshooting ………………………………………………………………………………………. 

Aussie Blaster Pressure Testing & Setting Instructions ………………………………...………...  

11 

Unloader Setting—Engine Powered Blaster ……………………………………………………….. 

12 

Pressure Testing & Unloader adjustment - Electric Powered Blasters …………………………. 

13 

Replacement Parts …………………………………………………………………………………… 

14 

Pump Exploded View ………………………………………………………………………………... 

15 

Service Schedule …………………………………………………………………………………….. 

16 

Before attempting to operate your machine please read this Instruction Manual thoroughly following all directions 
carefully.   By doing so you will ensure safe operation of the unit and will enjoy long and trouble free service from 
your heavy duty water blaster.

 

GUARANTEE … EXCLUSIVE 4 YEAR PUMP + 3 YEAR ENGINE WARRANTY 

This  Aussie  Eco  Clean  product  is  guaranteed  against  faults  in  manufacture  for  two  years  from  purchase.  The 
Bertolini pump has a four year warranty, but must be serviced by an authorised service agent every six months to 
maintain this warranty. Keep your receipt as proof of purchase and all service receipts.  This guarantee is invalid 
if the product is found to have been abused in any way, or not used for the purpose for which it was intended.   

Routine  maintenance  is  the  owner

=

s  responsibility.    Failure  to  maintain  the  machine  in  line  with  the  services 

outlined on the back page will invalidate warranty. High pressure accessories carry a 3 month warranty. 

Where possible return faulty goods to the place of purchase.  No products can be returned to us without our prior 
permission.  The reason for return must be clearly state. 

N.B. 

Warranty  is  not  transferrable  to  third  parties  in  the  event  of  sale  of  the  machine  within  the 
warranty period.  Please note that any parts used in warranty repairs are guaranteed for a period 
limited by the original warranty of the parent product. 

Engine  warranty  (where  applicable)  is  the  responsibility  of  the  engine  manufacturer.  Unit  must  be 
returned to authorised engine dealer for evaluation of engine warranty. (Refer to engine handbook). 

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled 
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or 
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality 
and the failure does not amount to a major failure. 

The benefits under the Aussie Pump warranty are in addition to other rights under Australian Consumer Law. 

Summary of Contents for BB100 Hire Series

















Reviews: