background image

Aussie BB Hire Series … Operation & Maintenance Manual 

Aussie Pumps 

June 2016 

 

B

.     Hose Connections 

 
1. 

Connect high pressure hose to machine outlet. 

2. 

Connect gun/lance assembly to high pressure hose.  

3. 

Check inlet water filter is clean then connect water supply hose to machine.  

Incoming  water  supply  must  deliver  double  the  flow  of  the  machine.  If  questionable,  check 
supply at machine. If supply is insufficient, do not operate from this outlet. For residential use, 
the outlet closest to the meter will usually deliver the highest flow rate.  Connect only to clean 
town water supply. 

Warning: 

Do not operate from tank or pond. Doing so will cavitate the pump causing damage. 

Cavitation or pump starvation is not covered by warranty. Cavitation is a phenomenon causing 
vacuum pockets to form within the pump that eventually implode under pressure pitting the 
internal pump surfaces. 

 

C.     Before starting the machine 

 
1. 

Ensure machine is level 

2. 

Turn on water supply. 

3. 

Pull gun trigger until water starts to flow in a steady stream then release trigger. 

 

D.  Starting the machine  

 

Engine Drive: 

OPERATE IN WELL VENTILATED AREAS 

ONLY

 
1. 

Ensure fuel valve is open 

2. 

Move the choke on the engine to the closed position If engine is warm, move choke half-way. 

3. 

Turn engine ON/OFF switch to ON 

4. 

Hold the gun trigger on. 

5. 

Start engine, pull the recoil starter grip lightly until resistance is felt, then pull briskly. 

6. 

After engine starts, release the gun trigger and slowly open the choke. 

7. 

Warm up engine for 3 minutes without load.  

8. 

Adjust speed control lever at to the required engine speed.  

Electric Drive: 

 
1. 

Ensure unit is plugged in to a suitable power supply. 

2. 

Hold the gun trigger on and turn on start switch. 

KEEP THE MACHINE OUT OF MOISTURE LADEN  ATMOSPHERES 

 

WEAR PROPER FACE PROTECTION WHEN OPERATING PRESSURE WASHER! 

 

NOTE

: Check the system for water leaks, fuel leaks, oil leaks, hose kinks, etc. Correct any problems before 

proceeding. 

HIGH PRESSURE SPRAY CAN PENETRATE THE SKIN AND CAUSE SERIOUS INJURY!  

NEVER POINT THE SPRAY GUN AT YOURSELF, OTHER PEOPLE OR ANIMALS.  

SHOULD SPRAY PENETRATE THE SKIN, SEEK MEDICAL ATTENTION IMMEDIATELY! 

Summary of Contents for BB100 Hire Series

















Reviews: