background image

11

To reduce the risk of serious bodily injury or death:

· Use only propane gas in this LP gas grill.  
· Do not attempt to convert an LP unit to natural gas.     
· Any use or alteration of this unit not intended could be 

unsafe and will void your warranty.

· Always use a gas appliance outdoors in an open area   

with good ventilation to avoid breathing toxic fumes 
from leaking gas, explosion or fire.  As with all
conventional fuels, the burning process consumes 
oxygen and produces toxic gases, including carbon 
monoxide. In addition, the combustion products of 
such fuels, including liquefied petroleum (LP), contain 
chemicals known to the state of California and other 
authorities to cause cancer, birth defects and other 
reproductive harm.

USING GAS

CARBON MONOXIDE HAZARD

· This appliance can produce carbon monoxide which 

has no odor. Using it in an enclosed space can kill you. 

· Never use this appliance indoors, on recreational 

vehicles, or boats.

OPERATING YOUR LP GAS GRILL

To reduce the risk of serious bodily injury, fire or death:

· Read and follow all warnings on LP gas cylinder.
· If you see, smell, or hear the hiss of LP gas 

escaping from the cylinder:
1. Do not attempt to light appliance. 
2. Extinguish any open flame.
3. Disconnect from fuel supply.

· Do not operate the LP gas grill without the LP gas 

cylinder secured to the cart and oriented as shown in 

Assembly Instructions for Connecting the LP Cylinder.

· Never connect or disconnect LP gas cylinder or

fittings while grill is in use or is hot. 

· When the LP gas cylinder is connected, keep the grill  

outside in a well-ventilated space. 

· Do not use an LP gas cylinder if it shows signs of 

dents, gouges, bulges, fire damage, corrosion,
leakage, excessive rust or other forms of visual
external damage; it may be hazardous and should be 
checked by a liquid propane supplier. Do not use an 
LP cylinder with a damaged valve.

· Do not store a spare LP gas cylinder under or near 

the LP gas grill.

·

When grill is not in use, turn off all grill control knobs, 

LP cylinder valve and disconnect LP cylinder. 

LP GAS CYLINDER

· The LP gas cylinder, for use with this LP gas grill, must meet 

the following requirements:  

1) 12” diameter x 18” tall, 20 lb.. maximum capacity 

2) Overfill Protection Device (OPD) safety feature (should 

be noted on cylinder) 

3) Must be constructed and marked in accordance with 

Specifications for LP-Gas Cylinders of the U.S. 
Department of Transportation (DOT) or the National 
Standard of Canada, CAN\CSA-B339, Cylinders, 
spheres and Tubes for Transportation of Dangerous 
Goods; and Commission, as applicable (See collar for 
marking)

4) Must have collar to protect LP cylinder valve.

LP HOSE AND REGULATOR

To reduce the risk of serious bodily injury or death:
· Clean and inspect the gas hose/regulator before each 

use of the outdoor cooking gas appliance. The gas 
hose/regulator must be replaced prior to being used, if 
there is evidence of excessive abrasion or wear, or if 
the hose is cut or leaks.

· Use only the gas hose/regulator assembly that has been 

supplied with this gas grill. Do not use hose/regulator 
from another manufacturer.

· Always check for gas leaks when you connect and

disconnect the hose/regulator to the LP gas cylinder,
especially after a period of storage (for example, over 
winter).

· Make sure there are no sharp bends in the hose.
· Make sure hose/regulator does not contact any heated  

surfaces.

· If the hose/regulator assembly is not working properly and 

you need a replacement, contact the manufacturer
(1-800-251-7558). Be sure to specify your grill model.

· 

Never fill the LP gas cylinder more than 80% of 

cylinder volume. (20 lb. maximum)  Do not ask the 
propane supplier to over-fill the cylinder.

·

If you obtain LP gas through a cylinder exchange

dealer, make sure you get a safe and adequate O.P.D. 
cylinder. (See page 22) Use only a licensed LP gas 
cylinder dealer.

·

Place dust cap on cylinder valve outlet whenever the

cylinder is not in use.  Only install the type of dust cap
on the cylinder valve outlet that is provided with the  
cylinder valve.  Other types of caps or plugs may result     
in leakage of propane.

Connecting the LP Cylinder:

1) Fill empty OPD LP Cylinder at your local LP 

gas supplier.

2) Make sure all control knobs and LP Cylinder 

valve are turned to the “Off” position.

CONNECTING/DISCONNECTING THE GAS

Summary of Contents for 7110.7.641
























Reviews: