Aussie Adventurer 2400 Owner & User Manual Download

Page: 15 / 26

IGNITION LIGHTING THE LANTERN

1. Check to make sure lantern parts are intact and not

disrupted and cylinder is properly connected.

2. Important: Make sure Lantern Control Knob is turned

“Off” first.

3. Turn the Control Knob to the ‘On” position until it

stops. (FIG. 15A)

4. Push the Ignitor button in several times to light. Listen

for the spark ignition and look to make sure the burner
is lit. If no spark, refer to the Troubleshooting
Section.

5. If Lantern fails to light, repeat Steps 3 and 4.

If Lantern fails to light after three or four attempts
following Steps 3-4, turn control knob to the “Off”
position. Wait five minutes; then repeat the lighting
procedure. Note: If the burner still fails to light, refer to
the Troubleshooting Section. The burner can also be lit
manually, see Manual Lighting Lantern.

6. After ignition, turn the control knob to adjust the

amount of light that is desired.

If the lantern burner goes out during operation, turn
control knob to the “Off” position. Wait five minutes
before attempting to relight the grill. If it does not
relight, turn control knob to the “Off” position. Make
sure there are no open flames in the grill, side burner
or nearby; then disconnect the cylinder and see if it is
empty.

Ignitor Button

Turn Control

knob to “On”

position.

FIG. 15A

4. If Lantern Burner fails to light, repeat Steps 2 and 3.

If burner fails to light after three or four attempts
following Steps 2-3, turn control knob to the the “Off”
position. Wait five minutes; then repeat the lighting
procedure. NOTE: If the burner still fails to light, refer
to the Troubleshooting Section.

5. After ignition, turn the control knob to the desired

setting for use.

If the Lantern goes out during operation, turn the
control knob to the “Off” position. Wait five minutes
before attempting to relight the grill. If it does not
relight, turn control knob to the “Off” position. Make
sure there are no open flames in the grill, side burner
or nearby; then disconnect the cylinder and see if it is
empty.

MANUAL LIGHTING THE LANTERN

FIG. 15B

Hold lit match

near burner.

Your burners have been preset by the manufacturer for
optimal flame performance. A blue flame, possibly with a

CHECK YOUR FLAME

Yellow Tip

Primarily

Blue

Flame

FIG. 16

Turn Control

knob to “On”

position.

Check the flame before each cooking session and throughout
the grilling season. Always check especially after long periods
of storing the grill. If the flame is significantly yellow in color,
the appropriate amount of LP gas in the air/LP gas mixture is
not correct. This could be due to a blocked burner from
grease drippings or from insects building a nest inside the
burner or burner opening. See How to Clean the Burners.

To reduce the risk of serious bodily injury or death:
· Use only 1 pound LP cylinder with Lantern.
· Do not use gas tube with Portable Lantern and 1 pound

LP cylinder. It is unstable and will cause lantern to tip
over and cause a fire.

· Make sure there are no obstructions to the flow of

combustion and ventilation air to the Lantern.

· Always burn lantern in upright position away from any

flammable substances.

· Use lantern for lighting only. Do not touch hot surfaces.
· Hold the lantern by the cylinder when transporting. Hold

it away from you and do not run with it.

· Always light and use lantern outdoors. Never use

indoors, on recreational vehicles, or boats.

· To avoid eye damage, do not stare into the intense light.
· Never operate lantern with a hole in the mantle or

overheating and fire hazard could result.

· Never operate lantern without a globe shield or top cap.
· To avoid burns, do not place your head or body over