Aussie Bonza Deluxe Series Use Manual Download

Page: 3 / 35

WARNING! If your grill catches on fire:

• If the fire is in the grill portion and you can

safely reach the control knobs, then turn them off by

turning knobs clockwise. If you cannot safely reach

the

control knobs, call the fire department.

• If the fire involves one of the hoses, and you

can safely reach the propane cylinder valve, shut

the valve off by turning LP cylinder valve handle

clockwise to a full stop.

• If the fire involves the cylinder, leave it alone,

evacuate the area and call the fire department.

• If there is any type of fire that threatens either

personal safety or endangers property, call the

fire department.

8. Check the Bottom Body Panel for grease buildup. Re-

move excess grease to avoid a grease fire in the

pan.

Never use the grill without Bottom Body Panel

and Grease Tray in place.

WARNING!

If you notice grease or other hot

material dripping from the grill onto valve, hose, or regu-

lator, turn off gas supply immediately. After the grill has

cooled,

determine the cause and correct it. After cleaning

the valve, hose and regulator, perform a leak test before

continuing use. See

Before Using Your LP Gas

Grill

section of this manual for correct leak test proce-

dures.

10. This installation must conform with local codes or, in

the absence of local codes, with either the National Fuel

Gas Code, ANSI Z223.1, or CAN/CGA-B149.2, Propane

Installation Code.

11. If an external electrical source is utilized, the

outdoor cooking appliance, when installed, must be

electrically grounded in accordance with local codes

or, in the absence of local codes, with the National

Electrical Codes, ANSI/NFPA 70, or the Canadian

Electrical Code. CSA C22.1.

12. Keep any electrical supply cord and the fuel supply

hose away from any heated surfaces. Electric cords

should be placed away from walkways to avoid a trip-

ping hazard.

13. Combustible materials should never be within 36 in. of

the back or sides of your LP gas grill.

14. Never apply polyurethane to the wood cart while the

grill is in use or hot. Allow polyurethane to completely

dry before using.

15. The Vinyl grill cover must be removed and placed

at least 36 inches from LP gas grill while in use. The

grill cover is made of a flammable material. The grill must

be cooled before putting the cover back on the grill.

16.

WARNING! Always Store Lp Cylinders

upright and where temperatures do not exceed 125

degrees Fahrenheit. Never store a spare or discon-

nected LP cylinder under or near this LP gas grill.

17. Check the LP gas grill for gas leaks and burner

obstructions before each use.

WARNING! Do not use a flame to check for

gas leaks.

See

Before Using Your LP Gas Grill

sec-

tion of this manual for correct leak test procedures. A

clogged

burner tube can lead to a fire beneath grill.

18.

DANGER! If you see, smell, or hear the hiss

of escaping gas from the LP cylinder:

A. Get away from the cylinder.

B. Do not attempt to correct the problem yourself.

C. Call your local fire department.

19.

WARNING! Do not operate an LP gas grill if

you have knowledge of or suspect a gas leak.

20. Always inspect the gas hose and regulator

assembly before each use. Always turn the LP cylinder

to the “Off” position before inspecting parts. If the hose is

cut,

damaged, or showing signs of excessive abrasion

or wear, do not use the LP gas grill. Contact the

manufacturer, as the hose must be replaced with

an assembly specified by the manufacturer prior to

further use of the LP gas grill.

21.

WARNING!

Before lighting the LP gas grill,

open the lid or hood to prevent an explosion from gas

build-up.

22. If any burner does not light, turn off all gas control

knobs. Leave the grill lid or hood open and wait five

minutes before attempting to light.

23. If any burner goes out during operation, turn off all

gas control knobs. Open the hood (on Bonza™) and

wait five minutes before attempting to light.

24. Exercise reasonable care when using this LP gas

grill. Never leave grill unattended during use or cleaning.

25. Never allow children to operate or play near an LP

gas grill. Keep animals and bystanders out of the grill

area.

26. Always turn off the LP gas cylinder at the cylinder

valve when not in use. Allow grill to cool before handling

parts or cleaning.

27.

WARNING

Do not move an LP gas grill when

in use or hot.

28.

WARNING!

Never touch hot surfaces. Use heat

resistant gloves, long-handled tongs, or cooking mitts

at all times. The grill will become very hot. Open the

Summary of Contents for Bonza Deluxe Series




































Search results

Summary of Contents for Bonza Deluxe Series

Reviews:

Related manuals for Bonza Deluxe Series

Brands by name

Popular brands

Aussie Bonza Deluxe Series, Use Manual

Search results

Summary of Contents for Bonza Deluxe Series

Reviews:

Related manuals for Bonza Deluxe Series

Brands by name

Popular brands