Aussie MONARO 7652K1 Assembly And Use Manual Download | Manualshive

Page: 7 / 16

background image

STEP 3-Wheel Assembly

(ITEM 9) Wheel

(ITEM 8) Washer

(Axle)

(ITEM 10) Axle Nut

7

· Remove Axle Nuts from Axle. Insert Axle through both sides of Wheel Legs. Place Axle Washers

onto each end of Axle.

· Position Wheel hub recess to the outside and slide a Wheel onto each end of Axle.

· Attach Axle Nut onto each end of Axle. Tighten each side with wrench or pliers.

Wheel hub recess

this side

Axle Washer

Axle Nut

7 with Item 10 installed

«
...
5
6
7
8
9
...
»

Summary of Contents for MONARO 7652K1

















Reviews:

No comments

Related manuals for MONARO 7652K1

Brand: Parkside Pages: 40

Brand: Parkside Pages: 80

Brand: Parkside Pages: 67

Brand: Parkside Pages: 76

Brand: Parkside Pages: 105

Brand: Parkside Pages: 61

Brand: SafeCourt Pages: 18

Brand: Jata electro Pages: 20

Brand: Livoo Pages: 24

Brand: Cadac Pages: 94

Brand: PALSON Pages: 17

FLAME ELITE 600D3E

Brand: Z GRILLS Pages: 30

Brand: Metabo Pages: 64

Brand: Nostalgia Electrics Pages: 30

Brand: BackyardGrill Pages: 14

Brand: Renaissance Pages: 12

Brand: Backyard Pro Pages: 30

Brand: Küchenprofi Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands