background image

1

1

2

5

7

8

9

11

12

13

1

2

3

4

5

6

7

8

9

CONVENTIONS

:     WARNINGS

:     ISTRUCTIONS

:     TECHNICAL DATA

In this manual, all important information is indicated using the following symbols and 
conventions:

:     IMPORTANT TEXTS

Index and Conventions 

Introduction to E16 series

SIRIO E, CONDOR E transmitting unit 

Warnings for use

Warnings for maintenance

Operation of SIRIO E, CONDOR E transmitting unit

Frequencies

Settings

SIRIO E, CONDOR E transmitting unit diagnostic

!

abcd. . . 

abcd. . . 

abcd. . . 

abcd. . . 

Page 1

Before installing, starting and using the radio remote control, this manual MUST be 
read and understood carefully by all people who install, use and carry out 
maintenance on the radio remote control.

If this manual is lost or damaged, 

ask for a copy from Autec.  

Please specify the serial number 

of the relative radio remote control.

Follow the indications and warnings 

given by the machine producer

 regarding the machine controlled 

by the radio remote control.

No parts of this manual may be reproduced 

by any means without the written permission of Autec

(Including recording and photocopying).

The information contained in this manual 

is subject to modification 

without notice and is not binding.

INDEX

E

N

G

L

IS

H

INDEX AND CONVENTIONS

Page

LIE16MU1

Summary of Contents for E16 Series














Reviews: