WARRANTY
If your supplier has not given advice or demonstration on how to set up or use our products,
please check with them before sending any goods back for warranty.
All Autocom products are warranted for a period of 12 months from the date of original
purchase, to the original purchaser, from an authorised Autocom retailer, against faulty
materials or workmanship, subject to the goods being used only as stated, and only for the
purpose as described in the instruction manuals.
No manufacturer's warranty applies to the goods where they are used for any other purpose
or in any other way than is explained in the instructions. Nor where the goods have been
subjected to misuse, neglect or accidental damage, or used with any other vendor’s products,
including incorrect mechanical or electrical installation, or where the goods have been
repaired, modified or altered, without the manufacturers written authorisation.
The manufacturer's warranty is limited to the goods being returned pre paid to the
manufacture's factory, with the original packaging and the original proof of purchase date.
The goods must be intact for our examination.
Where goods are accepted by the manufacturer, under the terms of the warranty, they will be
repaired free of charge or replaced (at the option of the manufacturer). Where the goods are
returned as faulty and are found not to be, an inspection, testing and return postage and
packing charge will be payable.
This warranty does not cover any consumable items such as batteries, replaceable hygiene
foam coverings for speakers & microphones, or any other items that are described within the
instruction manuals as being a consumable.
The manufacturer's warranty does not effect your statutory rights.
PLEASE CONTACT YOUR SUPPLIER OR AUTOCOM FOR ANY FURTHER
HELP OR INFORMATION.
We service what we sell
UK Manufacturer & Distributor. Autocom Products Ltd.
20 Hawkes Drive, Heathcote Industrial Estate, Warwick. CV34 6LX. England. Tel: +44 (0)1926 431249 Email
enquiries@autocom.co.uk
WEBSITE
www.autocom.co.uk
USA Distributor.
Top Gear NY 12159 USA Tel: 518 449 8677
www.autocomamerica.com
German Distributor.
Green Frog & JF Motor Sport Tel: +49 6002 911331
www.greenfrog.de
Netherlands & Belgium Distributor. Splash Design.
Tel: +31 413 389089
www.splashdesign.nl
Norway Distributor.
Spare Parts Service AS Norway Tel: 67 907800
www.sps.no
Finland Distributor.
Tokimoto Oy Finland Tel: +358 9 838 6540.
www.tokimoto.fi
Switzerland Distributor.
Hostettler A.G. Tel: 0041 41926 6111
www.hostettler.com
New Zealand Distributor.
Dold Industries Ltd 00647 849 4392
www.dold@ventura-bike.com
If you need support in any country not listed, please contact Autocom UK.
V3
It is VERY IMPORTANT that
you fully read & understand
ALL of these instructions
before installation & use
These parts are designed ONLY for
use with Autocom domestic
motorcycle communication systems
INSTRUCTION MANUAL & WARRANTY for
Part 150.
(BFK-U) Universal Bike Fitting Kit
This basic fitting kit gives you the typical parts that are frequently required for installing an Autocom system
to most types of bike. Please note that you may require some parts that are not included in the kit. This will
depend on the bike you have and how you want the intercom fitted. Please check with your supplier for more
advice. PLEASE NOTE all parts of this fitting kit are consumables and so have a limited warranty .
The kit includes
5
of
BLACK Tie wraps .
5
of
WHITE TIE wraps.
1
of 150mm
Hook Velcro (rough)
1
of 300mm
Loop Velcro (soft)
2
of
Black plastics clips.
1
of
Blue eyelet crimp terminal
1
of
Special electrical connector.(Fig 1 Part B)
1
of
Black self-amalgamating tape
1
of
3.2mm Black heat shrink tubing
TIE wraps
Use these where required to hold any cables in place. Make sure that you do not crush any
cables or tubing/breather/brake/clutch pipes on the bike by over tightening the tie wraps. Always cut the tie
wraps off squarely, as cutting them at an angle can leave a sharp pointed edge that can cause cuts.
Notes On Cables .
Extreme care should be taken to ensure that the cables do not fall into the chain, wheel
or foul the steering etc, or be trapped or crushed by the seat or body panels. Pay particular attention to the
seat locking mechanism, which, if fouled, could cause problems with removing the seat. If required, use
some hard packing strips bonded in place either side of the cables, to prevent damaging the cables at any
pressure points, such as where the cables come from under the seat between the tank or body panels.
Avoid any sharp angles or edges that may damage or cut the cables.
Velcro.
Cut one piece of hook and loop Velcro to about the same length as your intercom unit and use this
to fix the intercom to a clean, dry area, normally under the rear seat of the bike. (Ensure all surfaces are
clean and dry). If required use some of the remaining loop Velcro to cover any sharp edges, to protect the
cables.
Black clips.
These can be used to hold the rider & passenger headset sockets neatly in place on the bike.
Make sure that the surface is flat, clean and dry before applying. Please note that the clips will tear off in the
event of an accident. They can sometimes be refitted using some suitable double-sided tape/glue.
