NOTE Freezing the primary object’s layer (A-Wall in this case) makes the entire wall, including its internal
boundaries, invisible regardless of the value of this setting. This setting applies only to the Off layer state.
Then…
If you want to…
clear Immediate and independent layer on/off control of display
components.
turn off secondary object components on different layers
when the main component layer is turned off
select Immediate and independent layer on/off control of
display components.
turn on and off secondary object components independently
of the main object component layer settings
8
IMPORTANT If you select Save as Default, the layer key style you select is the default layer key style for all new
drawings created without a template or from templates that do not have different default layer key standards
assigned.
Save the layer settings:
Then…
If you want to…
select Save as Default, and click OK. Settings on the Units
and Scale tabs are also saved as default settings.
save the layers settings as default settings for all new drawings
that you start without a template or from templates that do
not contain drawing setup information
clear Save as Default, click Apply, and then click OK.
save the layer settings only for the current drawing
If you also changed the drawing units, you are prompted to specify whether existing objects in the current
drawing should be scaled for the new units. For more information, see “
Specifying the Drawing Units
” on
page 110.
Specifying the Default Display Representations
Use this procedure to specify the default display representations of AEC objects. You can also specify the default display
configuration for the Model tab and new viewports. In addition, you can specify whether the drawing uses its own
display configurations or those of a host drawing when the drawing is referenced as an overlay xref.
You may find it easier to select and modify display representations using the Display Manager. For more information
about the display system, see “
Display System
” on page 443. For more information about using the Display Manager,
see “
The Display Manager
” on page 457.
NOTE Changes you make on the Display tab apply only to the current drawing. New drawings are not affected. Save as
Default has no effect on this tab.
1
On the Drawing Window status bar, click
.
2
Click Drawing Setup.
NOTE Alternatively, you can choose Drawing Setup from the Format menu.
3
Click the Display tab.
4
To make changes to a display representation for an object type, select it, and click Edit.
For general information about display representations, see “
Display Representations
” on page 451. For
information about the display properties of an object type, see the chapter about the relevant object. For
example, for information about wall display properties, see “
Specifying the Display Properties of a Wall
Style
” on page 733.
5
Select a display configuration for Default Display Configuration.
The display configuration is applied to the Model tab and new viewports in paper space layouts.
114 | Chapter 4 Creating and Saving Drawings
Summary of Contents for 00128-051462-9310 - AUTOCAD 2008 COMM UPG FRM 2005 DVD
